Nissan Tiida C11. Instruction — part 203
DLK-222
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR
DOOR
Fitting Adjustment
INFOID:0000000001315837
FRONT DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
Access from inside the fender to loosen the hinge bolts. Raise the front door at rear end to adjust.
Surface Height Adjustment
Loosen the front door bolts, and adjust the surface height difference of fender and front door according to the
fitting standard dimension.
Striker Adjustment
1.
Front fender
2.
Front door outer
3.
Rear door outer
4.
Rear fender
5.
Front door weatherstrip
6.
Front door sash
7.
Rear door weatherstrip
8.
Rear door sash
PIIB6516E
DOOR
DLK-223
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
REAR DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
1.
Remove the center pillar upper and lower garnishes. Refer to
INT-20, "Removal and Installation"
.
2.
Access from inside the vehicle to loosen the hinge nuts. Open the rear door, and raise the rear door at
rear end to adjust.
Surface Height Adjustment
Loosen the front door striker bolts and rear door hinge nuts, and adjust the surface height difference of front
and rear doors according to the fitting standard dimension.
Striker Adjustment
1.
BACK DOOR
Longitudinal Clearance and Surface Height Adjustment
16.7 N·m (1.7 kg-m, 12 ft-lb)
PIIB2804J
16.7 N·m (1.7 kg-m, 12 ft-lb)
PIIB2804J
DLK-224
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR
1.
Open and support the back door.
2.
Slightly loosen the hinge nuts.
3.
Reposition the door as necessary and tighten the nuts.
4.
Confirm the adjustment. Repeat as necessary to obtain the desired fit.
Striker Adjustment
1.
Back door assembly
2.
Back door hinge
3.
Tail lamp assembly
4.
Back window glass
5.
Roof
6.
Rear pillar
A.
6.0
±
1.0 mm (0.24
±
0.04 in)
B.
-0.5
±
1.0 mm (-0.02
±
0.04 in)
C. 5.0
±
1.2 mm (0.20
±
0.05 in)
D.
0.0
±
1.5 mm (0.0
±
0.06 in)
E.
5.0
±
2.3 mm ( 0.20
±
0.9 in)
F.
2.7 +1.6 -2.1 mm (0.11 + 0.06 - 0.08 in)
G.
5.0
±
1.2 mm ( 0.20
±
0.05 in)
H. 0.0
±
1.5 mm (0.0
±
0.06 in)
LIIA2668E
DOOR
DLK-225
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Removal and Installation
INFOID:0000000001315838
FRONT DOOR
CAUTION:
• When removing and installing the front door assembly, support the door with a jack and cloth to pro-
tect the door and body.
• When removing and installing front door assembly, be sure to carry out the fitting adjustment. Refer
.
• After installing, apply touch-up paint onto the head of the hinge nuts.
• Check the hinge rotating part for lubrication. If necessary, apply “body grease”.
• Operate with two workers, because of its heavy weight.
• Check front door open/close operation after installation.
Removal
1.
Remove dash side finisher. Refer to
INT-20, "Removal and Installation"
2.
Disconnect the front door harness connectors.
3.
Remove the front door harness grommet, and then remove the
harness from the vehicle.
4.
Remove the check link bolt.
Striker bolts
20 N·m (2.2 kg-m, 16 ft-lb)
LIIA2641E
PIIB6518E
14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB6543E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст