Nissan Tiida C11. Instruction — part 204
DLK-226
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR
5.
Remove the hinge nuts and then the door assembly.
Installation
Installation is in the reverse order of removal.
REAR DOOR
CAUTION:
• When removing and installing the rear door assembly, support the door with a jack and cloth to pro-
tect the door and body.
• When removing and installing rear door assembly, be sure to carry out the fitting adjustment. Refer
.
• After installing, apply touch-up paint onto the head of the hinge nuts.
• Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
• Operate with two workers, because of its heavy weight.
• Check rear door open/close operation after installation.
Removal
1.
Remove the rear door harness grommet.
2.
Disconnect the rear door harness connector.
24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB6519E
PIIB6520E
PIIB6521E
DOOR
DLK-227
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove the check link bolt.
4.
Remove the hinge nuts and the door assembly.
Installation
Installation is in the reverse order of removal.
BACK DOOR
Removal
1.
Remove the back door glass. Refer to
GW-18, "Removal and Installation"
2.
Remove the back door lock assembly. Refer to
DLK-236, "Removal and Installation"
.
3.
Remove the back door wire harness.
4.
Remove the rear washer nozzle and hose from the back door. Refer to
5.
Support the back door.
CAUTION:
Two technicians should be used to avoid damaging the back door during removal.
6.
Remove the back door stays.
7.
Remove the door side nuts and the back door assembly.
Installation
Installation is in the reverse order of removal.
• Align the back door. Refer to
14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB6543E
24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB6522E
LIIA2639E
DLK-228
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Removal and Installation of Fuel Filler Lid Opener
INFOID:0000000001315839
REMOVAL
1.
Remove trunk side finisher (RH). Refer to
INT-35, "Removal and Installation"
.
2.
Remove fuel filler lid opener cable lock ring.
3.
Remove front and rear kicking plates. Refer to
INT-20, "Removal and Installation"
.
4.
Remove rear cushion assembly. Refer to
5.
Remove the bolts and the fuel filler lid opener handle.
6.
Remove fuel filler lid opener cable clips from the vehicle.
7.
Remove the fuel filler lid opener cable (LH drive).
8.
Remove the fuel filler lid opener cable (RH drive).
PIIB3831J
LIIA2670E
LIIA2629E
ALKIA0651GB
FUEL FILLER LID OPENER
DLK-229
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст