Nissan Tiida C11. Instruction — part 1426
VTL-40
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
A/C UNIT ASSEMBLY
43. Cooler pipe assembly
44.
Water temperature sensor
45.
Full hot switch
46. PTC heater
47.
PTC control unit
EVAPORATOR
VTL-41
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
EVAPORATOR
Removal and Installation of Evaporator
INFOID:0000000001696533
REMOVAL
1.
Remove A/C unit assembly. Refer to
VTL-37, "Removal and Installation"
.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2.
Remove the air conditioner filter.
3.
Remove foot duct (right). Refer to
VTL-48, "Removal and Installation"
.
4.
Remove screws (A), and then remove expansion valve cover
(1).
5.
Remove screws (A), and then remove evaporator cover (1).
6.
Remove the evaporator (1) with lower blower case (2) from the
A/C unit assembly.
7.
Remove the thermo control amp. (3) from the evaporator (1).
CAUTION:
Note the position of the thermo control amp. on the evapo-
rator for installation.
8.
Remove the evaporator (1) from the lower blower case (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace O-rings for A/C piping with new ones, and the apply compressor oil to it when installing it.
• Install the thermo control amp. in the same position on the evaporator.
• When recharging refrigerant, check for leaks.
SJIA0673E
SJIA0674E
SJIA0599J
VTL-42
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
HEATER CORE
HEATER CORE
Removal and Installation
INFOID:0000000001696534
REMOVAL
1.
Remove the A/C unit assembly. Refer to
VTL-37, "Removal and Installation"
.
2.
Remove the foot duct (left). Refer to
VTL-48, "Removal and Installation"
3.
Remove the heater pipe cover screw, then remove the heater pipe cover.
4.
Remove the heater pipe clip screw, then remove the heater pipe clip.
5.
Slide the heater core out of the A/C unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
1.
Heater pipe cover
2.
Heater pipe clip
3.
Heater core
A.
Heater pipe cover screw
B.
Heater pipe clip screw
LJIA0200E
BLOWER MOTOR
VTL-43
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
BLOWER MOTOR
Removal and Installation
INFOID:0000000001696535
REMOVAL
1.
Remove instrument panel and pad. Refer to
IP-11, "Removal and Installation"
.
2.
Remove side ventilator duct (right). Refer to
VTL-48, "Removal and Installation"
.
3.
Disconnect front blower motor connector (1).
4.
Push the flange holding hook (A) toward the front blower motor
(2), then rotate the front blower motor (2) clockwise and remove
it from the A/C unit assembly.
CAUTION:
When front blower fan and front blower motor are manufac-
tured, the balance is adjusted, do not disassemble to
replace the individual parts.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Rotate the front blower motor until the front blower motor flange holding hook locks securely into the
A/C unit assembly.
LJIA0199E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст