Nissan Tiida C11. Instruction — part 205
DLK-230
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
FRONT DOOR LOCK
FRONT DOOR LOCK
Component Parts Location
INFOID:0000000001315860
Removal and Installation
INFOID:0000000001315861
REMOVAL
1.
Remove front door finisher. Refer to
INT-13, "Removal and Installation"
2.
Fully close front door window.
3.
Remove the front door sealing screen.
NOTE:
If sealing screen is reused, cut butyl tape in a way that leaves it on the sealing screen.
4.
Remove front door rear glass run channel. Refer to
GW-14, "Removal and Installation"
5.
Remove the cables from the holder.
6.
Remove inside handle bolt, and slide the handle toward the rear
of the vehicle. disengage the handle from the door panel, and
remove the inside handle.
7.
Disengage the handle from the door panel, and remove the inside handle.
1.
Front door
2.
Inside handle
3.
Inside handle cable
4.
Door lock assembly
5.
Outside handle cable
6.
TORX bolt (T30)
7.
Key cylinder connecting rod
8.
Grommet
9.
TORX bolt (T30)
10. Rear gasket
11. Door key cylinder assembly
(Driver's side)
Outside handle escutcheon
(passenger's side)
12. Outside handle
13. Front gasket
14. Lock knob cable
15. Holder
16. Outside handle bracket
PIIB6523E
PIIB6524E
FRONT DOOR LOCK
DLK-231
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8.
Disconnect the inside handle cable and lock knob cable from the
inside handle.
CAUTION:
During removal and installation, work so as not to bend the
ends of the lock knob cable and inside handle cable.
9.
Remove the door side grommet, and the door key cylinder
assembly (escutcheon) bolt.
10. Remove the key cylinder connecting rod (key cylinder side).
11. If equipped, disconnect the door antenna, the door request
switch connector and remove the harness clamp. (Vehicle with
intelligent key systems only).
12. Remove the door cylinder assembly while pulling the outside
handle forward.
13. Pull the outside door handle forward and then slide it toward the
rear of the vehicle to remove.
14. Remove the front and rear gaskets.
PIIB6525E
PIIB5808E
PIIB5809E
PIIB5810E
PIIB6526E
DLK-232
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
FRONT DOOR LOCK
15. Remove the door lock assembly bolts.
16. Slide the outside handle bracket toward the rear of the vehicle,
and remove the assembly.
17. If equipped, disconnect the door lock assembly electrical connector.
18. Separate the outside handle cable from the outside handle
bracket.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• To install each rod, be sure to rotate the rod holder until a click is felt.
• When installing door lock assembly, be careful when rotating the outside handle cable as shown in
the figure.
- Place the outside handle bracket cable on the inside of door
lock assembly before installing.
5.8 N·m (0.6 kg-m, 51.4 in-lb)
PIIB6527E
PIIB6528E
PIIB5815E
PIIB6529E
REAR DOOR LOCK
DLK-233
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK
Component Parts Location
INFOID:0000000001315858
Removal and Installation
INFOID:0000000001315859
REMOVAL
1.
Remove the partition glass. Refer to
GW-18, "Removal and Installation"
2.
Support door glass while lifting it up to the door window completely closed position.
3.
Remove inside handle bolt, slide handle toward rear of vehicle,
disconnect it from the door panel, and remove the inside handle.
4.
Disconnect the inside handle and lock knob cables from the
inside handle.
CAUTION:
During removal and installation, do not to bend the ends of
the lock knob cable and inside handle cable.
1.
Rear door
2.
Inside handle
3.
Inside handle cable
4.
Door lock assembly
5.
TORX bolt (T30)
6.
Outside handle cable
7.
Grommet
8.
TORX bolt (T30)
9.
Rear gasket
10. Outside handle escutcheon
11. Outside handle
12. Front gasket
13. Lock knob cable
14. Outside handle bracket
PIIB6530E
PIIB6524E
PIIB6525E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст