Nissan Tiida C11. Instruction — part 1164
SEC-28
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2190, P1614 NATS ANTENNA AMP.
6.
CHECK NATS ANTENNA AMP. SIGNAL LINE- 2
Check voltage between NATS antenna amp. connector M21 terminal
3 and ground with analog tester.
Is the inspection result normal?
YES
>> NATS antenna amp. is malfunctioning.
NO
>> • Repair or replace harness.
NOTE:
If harness is OK, replace BCM, refer to
BCS-57, "Removal and Installation of BCM"
tialization with CONSULT-III. For initialization, refer to “CONSULT-III Operation Instruction”.
ALKIA0850ZZ
Terminals
Position of ignition key cylinder
Voltage (V)
(Approx.)
( + )
( - )
3
Ground
Before inserting ignition key
Battery voltage
After inserting ignition key
Pointer of tester should move for approx. 30 seconds,
then return to battery voltage
Just after turning ignition switch
ON
Pointer of tester should move for approx. 1 second, then
return to battery voltage
B2191, P1615 DIFFERENCE OF KEY
SEC-29
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2191, P1615 DIFFERENCE OF KEY
Description
INFOID:0000000001404063
Performs ID verification through BCM when ignition knob switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered ID of mechanical key is used.
DTC Logic
INFOID:0000000001404064
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Insert mechanical key into the key cylinder.
2.
Press the ignition knob switch.
3.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000001404065
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to CONSULT-III Operation Instruction.
Can the system be initialized and can the engine be started with re-registered mechanical key?
YES
>> Mechanical key was unregistered.
NO
>>
BCM is malfunctioning.
• Replace BCM. Refer to
XX-XX, "*****"
.
• Perform initialization again
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2191
DIFFERENCE OF
KEY
The ID verification results between BCM and me-
chanical key are NG. The registration is necessary.
Mechanical key
P1615
SEC-30
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2192, P1611 ID DISCORD, IMMU-ECM
B2192, P1611 ID DISCORD, IMMU-ECM
Description
INFOID:0000000001404066
BCM performs the ID verification with ECM that allows the engine to start. BCM starts the communication with
ECM if ignition switch is turned ON and starts the engine if the ID is OK. ECM prevents the engine from start-
ing if the ID is not registered.
DTC Logic
INFOID:0000000001404067
DTC DETECTION LOGIC
NOTE:
• If DTC B2192 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2192 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000001404068
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to CONSULT-III Operation Instruction.
Can the system be initialized and can the engine be started with re-registered mechanical key?
YES
>> ID was unregistered.
NO
>> GO TO 2.
2.
PEPLACE BCM
1.
Replace BCM. Refer to
XX-XX, "*****"
.
2.
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to CONSULT-III Operation Instruction .
Can the system be initialized and can the engine be started with re-registered mechanical key?
YES
>> BCM is malfunctioning.
NO
>> GO TO 3.
3.
PEPLACE ECM
1.
Replace ECM. Refer to the following page.
-
HR16DE (WITH EUR-OBD):
XX-XX, "*****"
-
HR16DE (WITHOUT EUR-OBD):
XX-XX, "*****"
-
MR18DE (WITH EURO-OBD):
XX-XX, "*****"
-
MR18DE (WITHOUT EURO-OBD):
XX-XX, "*****"
-
K9K:
XX-XX, "*****"
2.
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to CONSULT-III Operation Instruction.
Can the system be initialized and can the engine be started with re-registered mechanical key?
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2192
ID DISCORD BCM-
ECM
The ID verification results between BCM and ECM
are NG. The registration is necessary.
• BCM
• ECM
P1611
B2192, P1611 ID DISCORD, IMMU-ECM
SEC-31
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
YES
>> ECM is malfunctioning.
NO
>> GO TO 4.
4.
CHECK INTERMITENT INCIDENT
GI-55, "Intermittent Incident"
.
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст