Nissan Sentra. Instruction — part 482
FRONT COMBINATION LAMP
EXL-131
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000009757560
Disassembly and Assembly
INFOID:0000000009757561
DISSASSEMBLY
WARNING:
Do not touch bulb while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
• Do not leave the bulb out of the lamp reflector for a long time because dust, moisture, smoke, etc.
may affect the performance of the lamp.
1. Remove front combination lamp. Refer to
EXL-119, "Removal and Installation"
.
2. Rotate the covers counterclockwise and remove.
3. Rotate the halogen lamp bulb (low beam) counterclockwise and remove.
4. Disconnect the harness connector from the halogen lamp bulb (low beam) and remove.
5. Rotate the halogen lamp bulb (high beam) counterclockwise and remove.
6. Disconnect the harness connector from the halogen lamp bulb (high beam) and remove.
7. Rotate the side marker bulb socket counterclockwise and remove.
8. Remove the side marker bulb from the side marker bulb socket.
1.
Large cover (not serviceable)
2. Small cover (not serviceable)
3.
Front combination lamp
4.
Halogen lamp bulb (high beam)
5. Turn signal lamp bulb
6.
Turn signal lamp bulb socket
7.
LED harness connector
8. Halogen lamp bulb (high beam)
harness connector
9.
Halogen lamp bulb (low beam)
harness connector
10. Halogen lamp bulb (low beam)
11. Side marker lamp bulb socket
12. Side marker lamp bulb
ALLIA1203ZZ
EXL-132
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT COMBINATION LAMP
9. Rotate the turn signal bulb socket counterclockwise and remove.
10. Remove the turn signal bulb from the turn signal bulb socket.
11. Disconnect the harness connector from the LED circuit board and remove the harness.
ASSEMBLY
Assembly is in the reverse order of disassembly.
CAUTION:
After installing, be sure to install the bulb sockets securely to ensure watertightness.
REAR COMBINATION LAMP
EXL-133
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Exploded View
INFOID:0000000009757562
Disassembly and Assembly
INFOID:0000000009757563
DISASSEMBLY
WARNING:
Do not touch bulb while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
• Do not leave the bulb out of the lamp reflector for a long time because dust, moisture, smoke, etc.
may affect the performance of the lamp.
1. Remove rear combination lamp. Refer to
EXL-126, "Removal and Installation"
2. Rotate rear turn signal lamp bulb socket counterclockwise to remove from rear combination lamp.
3. Remove the rear turn signal lamp bulb from bulb socket.
4. Rotate back-up lamp bulb socket counterclockwise to remove from rear combination lamp.
5. Remove the back-up lamp bulb from bulb socket.
6. Disconnect the harness connector from the LED lamp.
ASSEMBLY
1.
Rear combination lamp
2. Rear turn signal lamp bulb
3. Rear turn signal lamp socket
4.
LED lamp harness connector
5. Rear combination lamp harness
connector
6. Back-up lamp bulb socket
7.
Back-up lamp bulb
ALLIA1210ZZ
EXL-134
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR COMBINATION LAMP
Assembly is in the reverse order of disassembly.
CAUTION:
After installing, be sure to install the bulb sockets securely to ensure watertightness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст