Nissan Quest E52. Instruction — part 435
DLK-454
< REMOVAL AND INSTALLATION >
BACK DOOR
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000009649458
Check the clearance and the surface height between back door and each part by seeing and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Back door
2.
Back door hinge
3.
Back door striker
4.
TORX bolt
5.
Bumper rubber
6.
Roof panel
7.
Side window glass
8.
Back door glass
9.
Slide door rail cover
10. Sight shield
11. Rear bumper fascia
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Difference
(RH/LH)
Back door – Roof panel
A – A
F
Clearance
5.5 – 8.5 mm (0.217 – 0.335 in)
—
G
Surface
height
0.0 – 2.0 mm (0.000 – 0.079 in)
—
JMKIB0755GB
BACK DOOR
DLK-455
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FITTING ADJUSTMENT PROCEDURE
1.
Loosen back door striker mounting bolts.
2.
Loosen back door hinge mounting nuts (back door side).
3.
Adjust back door using back door striker and back door hinge to the specified value, as shown in the fol-
lowing table.
4.
After adjustment tighten back door striker mounting bolts and back door hinge mounting nuts (back door
side) to the specified torque.
5.
Viewing from vehicle upper, insert bumper rubber (1) into bumper rubber bracket (2) to the position of
alignment mark (B).
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• After installation, apply touch-up paint (the body color) onto the head of back door hinge mounting
nuts.
• Adjust the following parts.
- Rear view camera.
• DISPLAY AUDIO: Refer to
.
• BASE AUDIO WITH SEPARATE DISPLAY: Refer to
• BOSE AUDIO WITHOUT NAVIGATION: Refer to
.
• BOSE AUDIO WITH NAVIGATION: Refer to
AV-528, "CALIBRATING CAMERA IMAGE (AROUND VIEW
.
BACK DOOR STRIKER ADJUSTMENT
Adjust back door striker so that it becomes parallel with back door lock insertion direction.
BACK DOOR STRIKER
BACK DOOR STRIKER : Removal and Installation
INFOID:0000000009649459
REMOVAL
1.
Remove tailgate kicking plate. Refer to
INT-40, "TAILGATE KICKING PLATE : Removal and Installation"
.
2.
Remove mounting TORX bolts, and then remove back door striker.
Back door glass – Side win-
dow glass
B – B
H
Surface
height
(
−
1.6) – (+2.4) mm [(
−
0.063) –
(+0.094) in]
1.5 mm
(0.059 in)
I
Clearance
3.0 – 7.0 mm (0.118 – 0.276 in)
—
Back door – Slide door rail
cover
C – C
J
Clearance
4.0 – 8.0 mm (0.157 – 0.315 in)
—
K
Surface
height
(
−
1.5) – (+1.5) mm [(
−
0.059) –
(+0.059) in]
—
Back door – Sight shield
D – D
L
Clearance
3.3 – 6.7 mm (0.130 – 0.264 in)
—
M
Surface
height
(
−
1.7) – (+1.7) mm [(
−
0.067) –
(+0.067) in]
—
Back door – Rear bumper
fascia
E – E
N
Clearance
6.0 – 10.0 mm (0.236 – 0.394 in)
—
Portion
Standard
Difference
(RH/LH)
JMKIA8349ZZ
DLK-456
< REMOVAL AND INSTALLATION >
BACK DOOR
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check back door open/close operation after installation.
• When removing and installing back door striker, check to perform the fitting adjustment. Refer to
DLK-454, "BACK DOOR ASSEMBLY : Adjustment"
BACK DOOR HINGE
BACK DOOR HINGE : Removal and Installation
INFOID:0000000009649460
CAUTION:
• Operate with two workers, because of its heavy weight.
• Use protective tape or cloth to protect from damage during remove and installation.
REMOVAL
1.
Remove back door assembly. Refer to
DLK-451, "BACK DOOR ASSEMBLY : Removal and Installation"
2.
Remove back door hinge mounting nuts (body side), and then remove back door hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check back door open/close operation after installation.
• When removing and installing back door assembly, perform the fitting adjustment. Refer to
"BACK DOOR ASSEMBLY : Adjustment"
.
• After installation, apply touch-up paint (the body color) onto the head of back door hinge mounting
nuts.
• Check back door hinge rotating part for poor lubrication. If
necessary, apply body grease.
BACK DOOR STAY
BACK DOOR STAY : Removal and Installation
INFOID:0000000009649461
REMOVAL
1.
Support back door lock with the proper material to prevent it from falling.
WARNING:
Body injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
2.
Remove back door stay mounting bolts.
CAUTION:
Be careful not to damage painted surface.
: Grease up point
JMKIA5659ZZ
BACK DOOR
DLK-457
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove the metal clip (3) located on the connection between
the back door stay (1) and the stud ball (2) (body side) by using
a flat-bladed screwdriver (A).
CAUTION:
Be careful not to damage painted surface.
4.
Remove back door stay.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Check back door open/close operation after installation.
BACK DOOR STAY : Disposal
INFOID:0000000009649462
1.
Fix back door stay (1) using a vise (C).
2.
Using hacksaw (A) slowly make 2 holes in the back door stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on back door stay, always cover a
hacksaw using a shop cloth (B) to avoid scattering metal
fragments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
BACK DOOR WEATHER-STRIP
BACK DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000009649463
REMOVAL
1.
Remove back door support rod (back door side). Refer to
DLK-477, "BACK DOOR SUPPORT ROD :
.
2.
Pull up and remove engagement with body from weather-strip joint.
CAUTION:
Never pull strongly on weather-strip.
INSTALLATION
1.
Working from the upper section, align weather-strip center mark with vehicle center position mark and
install weather-strip onto the vehicle.
JMKIA2255ZZ
JMKIA3336ZZ
A:
20 mm (0.787 in)
B:
Cut at the groove.
JMKIA3609ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст