Nissan Quest E52. Instruction — part 436
DLK-458
< REMOVAL AND INSTALLATION >
BACK DOOR
2.
Align the connecting point (B) of weather-strip (2) to the center
(A) of striker (1), and then install as shown in the figure.
3.
Pull weather-strip gently to ensure that there is no loose section.
NOTE:
Check that weather-strip is fit tightly at each corner and tailgate kicking plate.
4.
Install back door support rod (back door side). Refer to
DLK-477, "BACK DOOR SUPPORT ROD :
.
JMKIA5662ZZ
HOOD LOCK
DLK-459
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD LOCK
Exploded View
INFOID:0000000009649464
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000009649465
REMOVAL
1.
Remove front grille. Refer to
EXT-18, "Removal and Installation"
2.
Remove mounting bolts, and then remove hood lock assembly
(1).
NOTE:
Press the lever downward to avoid pin (A), then pull out hood
lock assembly upward.
CAUTION:
Never bend hood lock control cable (2) strongly.
1.
Hood lock assembly
2.
Hood lock control cable
3.
Hood lock control handle
: Clip
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIA8249GB
JMKIA8250ZZ
DLK-460
< REMOVAL AND INSTALLATION >
HOOD LOCK
3.
Disconnect hood lock control cable (2) from hood lock assembly
(1).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installation, perform hood fitting adjustment. Refer to
DLK-425, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation
INFOID:0000000009649466
REMOVAL
1.
Disconnect hood lock control cable from hood lock assembly. Refer to
2.
Remove fender protector LH (front and rear). Refer to
EXT-23, "Removal and Installation"
.
3.
Remove hood lock cable fixing clips.
4.
Disconnect hood lock control cable from hood lock control handle. Refer to
CONTROL HANDLE : Removal and Installation"
.
5.
Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never to damage (peeling) the outside of hood lock control cable.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never to bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark) properly.
• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to
DLK-425, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK CONTROL HANDLE
JMKIA8251ZZ
PIIB5801E
HOOD LOCK
DLK-461
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD LOCK CONTROL HANDLE : Removal and Installation
INFOID:0000000009649467
REMOVAL
1.
Remove mounting bolts, and then hood lock control handle.
2.
Remove fuel filler lid opener cable. Refer to
DLK-480, "FUEL FILLER OPENER CABLE : Removal and
.
3.
Remove hood lock control cable (2) from hood lock opener lever
(1).
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000009649468
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that secondary latch (3) is securely engaged with securely secondary striker (4) from the dead load
of the hood assembly.
2.
Check that primary latch (2) is securely engaged with primary striker (1) when hood assembly is closed
[free-fall from approximately 200 mm (7.874 in) height].
CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.
3.
While operating the hood opener carefully, check that the front end of the hood is lifted by approximately
20 mm (0.787 in) (A). Also, check that the hood opener returns to the original position.
4.
Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] (B).
JMKIA5901ZZ
1.
Primary striker
2.
Primary latch
3.
Secondary latch
4.
Secondary striker
JMKIA5673ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст