Nissan Quest E52. Instruction — part 434
DLK-450
< REMOVAL AND INSTALLATION >
SLIDE DOOR GUIDE RAIL
4.
Remove upper roller assembly and sub roller as a set. Refer to
DLK-441, "UPPER ROLLER : Removal
5.
Remove mounting nuts, and then remove slide door upper guide rail.
INSTALLATION
Install in the reverse order of removal.
SLIDE DOOR REAR GUIDE RAIL
SLIDE DOOR REAR GUIDE RAIL : Removal and Installation
INFOID:0000000009649454
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing slide door assembly, support door with a jack and shop cloth to pro-
tect door and body.
• Perform the following procedures after replacing guide rail.
- Paint rail the same color as the vehicle body.
- Apply anti-corrosion treatment to installation surface between body panel and rail.
- Adjust fitting of slide door after installation. Refer to
DLK-440, "DOOR ASSEMBLY : Adjustment"
.
REMOVAL
1.
Remove slide door assembly. Refer to
DLK-438, "DOOR ASSEMBLY : Removal and Installation"
2.
Remove slide door rail cover. Refer to
EXT-43, "Removal and Installation"
3.
Remove rear roller. Refer to
DLK-442, "REAR ROLLER : Removal and Installation"
4.
Remove luggage side lower finisher. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER : Removal
5.
Remove mounting TORX bolts and nuts, and then remove slide door rear guide rail.
INSTALLATION
Install in the reverse order of removal.
SLIDE DOOR LOWER GUIDE RAIL
SLIDE DOOR LOWER GUIDE RAIL : Removal and Installation
INFOID:0000000009649455
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing slide door assembly, support door with a jack and shop cloth to pro-
tect door and body.
• Perform the following procedures after replacing guide rail.
- Paint rail the same color as the vehicle body.
- Apply anti-corrosion treatment to installation surface between body panel and rail.
- Apply anti-corrosion treatment to each end of mounting nuts and stud bolts of rail.
- Adjust fitting of slide door after installation. Refer to
DLK-440, "DOOR ASSEMBLY : Adjustment"
.
REMOVAL
1.
Remove slide door assembly. Refer to
DLK-438, "DOOR ASSEMBLY : Removal and Installation"
2.
Remove rear kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and Installation"
3.
Remove mounting bolts, and then remove rear floor step assembly.
4.
Remove slide door lower striker. Refer to
DLK-446, "SLIDE DOOR LOWER STRIKER : Removal and
.
5.
Remove slide door lower stopper. Refer to
DLK-446, "SLIDE DOOR LOWER STOPPER : Removal and
.
6.
Remove lower roller. Refer to
DLK-442, "LOWER ROLLER : Removal and Installation"
.
7.
Remove mounting nuts, and then remove slide door lower guide rail.
INSTALLATION
Install in the reverse order of removal.
BACK DOOR
DLK-451
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
Exploded View
INFOID:0000000009649456
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009649457
CAUTION:
• Operate with two workers, because of its heavy weight.
• Use protective tape or cloth to protect from damage during remove and installation.
REMOVAL
1.
Remove back door support rod (back door side). Refer to
DLK-477, "BACK DOOR SUPPORT ROD :
(automatic back door models).
2.
Remove back pillar garnish LH and RH. Refer to
INT-27, "BACK PILLAR GARNISH : Removal and Instal-
.
1.
Back door weather-strip
2.
Back door hinge
3.
Stud ball
4.
Bumper rubber
5.
Back door stay
6.
Back door stay bracket
7.
Back door striker
8.
Back door panel
9.
Back door damper
A.
Center mark
B.
Seam
: N·m (kg-m, ft-lb)
: Body grease
JMKIA9365GB
DLK-452
< REMOVAL AND INSTALLATION >
BACK DOOR
3.
Disconnect harness connectors (1) and remove harness fixing
clip (A).
4.
Remove grommet (1), and then pull out harness from back main
pillar (2).
5.
Lower rear portion of headlining and secure work space.
a.
Remove rear pillar garnish LH and RH. Refer to
INT-27, "REAR PILLAR GARNISH : Removal and Instal-
.
b.
Remove roof side garnish LH and RH. Refer to
INT-28, "ROOF SIDE GARNISH : Removal and Installa-
c.
Remove upper side of back door weather-strip. Refer to
DLK-457, "BACK DOOR WEATHER-STRIP :
.
d.
Remove second assist grips LH and RH, third assist grips LH
and RH and third seat belt finisher LH and RH, and then remove
rear portion of headlining. Refer to
.
6.
Remove fixing clip (A), and then disconnect rear washer tube
(1).
: Vehicle front
JMKIA6227ZZ
: Vehicle front
JMKIA6228ZZ
JMKIA6229ZZ
: Vehicle front
JMKIA6230ZZ
BACK DOOR
DLK-453
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
7.
Remove grommet (1), and then pull out washer tube from roof
panel (2).
8.
Support back door lock with the proper material to prevent it from falling.
WARNING:
Body injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
9.
Remove back door stay (back door side). Refer to
DLK-456, "BACK DOOR STAY : Removal and Installa-
10. Remove back door hinge mounting nuts on back door and remove back door assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check back door open/close, lock/unlock operation after installation.
• After installation, perform fitting adjustment. Refer to
DLK-454, "BACK DOOR ASSEMBLY : Adjust-
: Vehicle front
JMKIA6231ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст