Nissan Quest E52. Instruction — part 817
INSTRUMENT PANEL ASSEMBLY
IP-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
i.
Remove clips (A).
ii.
Pull back instrument lower cover center (1), and then disengage pawl and metal clips.
iii.
Disconnect harness connector and remove harness clip.
b.
With NAVI
i.
Remove clips (A).
ii.
Pull back instrument lower cover center (2), and then disengage metal clips.
iii.
Disconnect harness connector and remove harness clip.
10. Remove instrument lower panel LH.
a.
Remove hood opener and fuel lid opener lever fixing bolts. Refer to
b.
Pull back instrument lower panel LH, and then disengage pawls and metal clips.
CAUTION:
Never pull instrument lower panel LH forcefully.
c.
Release data link connector (pawls) then remove it from instrument lower panel LH.
d.
Disconnect harness connectors, aspirator duct and remove harness clip.
11. Remove instrument finisher A.
a.
Pull back instrument finisher A, and then disengage metal clips.
b.
Disconnect harness connectors.
CAUTION:
Never pull instrument finisher A forcefully.
12. Remove instrument finisher B.
: Pawl
: Metal clip
JMJIA6136ZZ
: Metal clip
JMJIA6137ZZ
IP-18
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
a.
Lift up instrument finisher B lower right side, and then disengage
metal clips.
b.
Pull back instrument finisher B upper right side, and then disen-
gage metal clips.
c.
Pull back instrument finisher B left side, and then disengage
metal clips.
13. Remove driver air bag module. Refer to
SR-12, "Removal and Installation"
.
14. Remove steering wheel assembly. Refer to
ST-12, "Removal and Installation"
15. Remove steering column covers.
a.
Remove steering column cover fixing screws (A).
b.
Pull up steering column upper cover (1), and then remove steer-
ing column upper cover.
c.
Pull down steering column lower cover (2), and then remove
steering column lower cover.
16. Remove spiral cable. Refer to
SR-15, "Removal and Installation"
.
17. Remove combination switch. Refer to
BCS-99, "Removal and Installation"
18. Remove cluster lid A.
a.
Disconnect harness connectors (A).
b.
Pull back cluster lid A right side, and then disengage the pawls and metal clips.
: Metal clip
JMJIA6138ZZ
JMJIA6139ZZ
JMJIA6140ZZ
INSTRUMENT PANEL ASSEMBLY
IP-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
c.
Pull back cluster lid A left side, and then disengage the pawls and metal clips.
CAUTION:
Cover steering shaft with a shop cloth (B) to prevent it from being damaged.
19. Remove combination meter. Refer to
.
20. Remove BCM. Refer to
BCS-98, "Removal and Installation"
.
21. Remove optical sensor. Refer to
EXL-108, "Removal and Installation"
22. Remove sunload sensor. Refer to
HAC-147, "Removal and Installation"
.
23. Remove front body side welt RH. Refer to
INT-23, "BODY SIDE WELT : Removal and Installation"
.
24. Remove instrument side finisher RH.
a.
Insert a remover tool (A) into lower space.
b.
Pull the instrument side finisher RH crosswise, and then disen-
gage the pawls
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
25. Remove front pillar garnish RH. Refer to
INT-21, "FRONT PILLAR GARNISH : Removal and Installation"
26. Remove front pillar lower garnish RH. Refer to
INT-22, "FRONT PILLAR LOWER GARNISH : Removal
27. Remove speaker grille RH.
a.
Pull up speaker grille RH, and then disengage pawl.
b.
Pull back speaker grille RH, and then disengage metal clips.
28. Remove front squawker RH. Refer to the following.
• For Display audio: Refer to
AV-114, "Removal and Installation"
.
• For Base audio with separate display: Refer to
AV-254, "Removal and Installation"
• For Bose audio without navigation: Refer to
AV-409, "Removal and Installation"
.
• For Bose audio with navigation: Refer to
AV-615, "Removal and Installation"
.
: Pawl
: Metal clip
JMJIA6141ZZ
: Pawl
JMJIA6142ZZ
: Pawl
: Metal clip
JMJIA6143ZZ
IP-20
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
29. Remove disc eject switch. Refer to
AV-37, "Removal and Installation"
(for Base audio without separate
disc) or
AV-112, "Removal and Installation"
(for Display audio).
30. Remove instrument lower panel center.
a.
Remove fixing screw (A).
b.
Pull back instrument lower panel center, and then disengage
pawls and metal clips.
c.
Disconnect harness connectors.
31. Remove AV C/U. Refer to
AV-37, "Removal and Installation"
(for Base audio without separate disc) or
112, "Removal and Installation"
(for Display audio).
32. Remove instrument finisher C.
a.
Remove fixing screw (A).
b.
Insert a remover tool (A) into instrument finisher C right side,
and then disengage metal clips as shown in the figure.
CAUTION:
• Remove metal clips slowly so that they are not damaged.
• Never pull instrument finisher C forcefully.
c.
Insert a remover tool (A) into instrument finisher C upper side,
and then disengage metal clips as shown in the figure.
CAUTION:
• Apply protective tape (B) on the part to protect it from
damage.
• Remove metal clips slowly so that they are not damaged.
• Never pull instrument finisher C forcefully.
: Pawl
: Metal clip
JMJIA6144ZZ
JMJIA6145ZZ
: Metal clip
JMJIA6146ZZ
: Metal clip
JMJIA6147ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст