Nissan Quest E52. Instruction — part 818
INSTRUMENT PANEL ASSEMBLY
IP-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
d.
Insert a remover tool (A) into lower left side, and then disengage
metal clips as shown in the figure.
CAUTION:
• Apply protective tape (B) on the part to protect it from
damage.
• Remove metal clips slowly so that they are not damaged.
• Never pull instrument finisher C forcefully.
e.
Bypassing hooks, pull back instrument finisher C.
33. Remove selector lever knob. Refer to
TM-154, "Removal and Installation"
.
34. Remove cluster lid C.
a.
Remove fixing screws (A).
b.
Hold both cluster lid C and pull it out towards vehicle rear, and
then disengage metal clips.
c.
Disconnect harness connectors and remove harness clip.
35. Remove cluster lid D.
a.
Remove fixing screws (A).
: Metal clip
JMJIA6148ZZ
JMJIA6149ZZ
: Metal clip
JMJIA6150ZZ
JMJIA6151ZZ
IP-22
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
b.
Insert a remover tool (A) into cluster lid D LH and RH lower
space, and then disengage pawls as shown in the figure.
c.
Insert a remover tool (A) into cluster lid D LH and RH side
space, and then disengage pawls as shown in the figure.
CAUTION:
• Apply protective tape (B) on the part to protect it from
damage.
• Remove metal clips slowly so that they are not damaged.
• Never pull cluster lid D forcefully.
d.
Pull back cluster lid D, and then disengage the pawls.
36. Remove front display. Refer to the following.
• For Base audio with separate display: Refer to
AV-251, "Removal and Installation"
• For Bose audio without navigation: Refer to
AV-405, "Removal and Installation"
.
• For Bose audio with navigation: Refer to
AV-611, "Removal and Installation"
.
37. Remove center speaker grille (With BOSE audio and navigation).
a.
Insert a remover tool (A) between center speaker grille and
instrument panel assembly to disengage pawls as shown in the
figure.
b.
Pull up center speaker grille.
CAUTION:
• Apply protective tape (B) on the part to protect it from
damage.
• Remove pawls slowly so that they are not damaged.
38. Remove center squawker (With BOSE audio and navigation). Refer to
AV-619, "Removal and Installa-
39. Remove glove box assembly.
a.
Slightly open glove box assembly.
b.
Pull the glove box assembly diagonally toward vehicle rear
upper direction to remove glove box assembly from instrument
lower panel RH.
: Pawl
JMJIA6152ZZ
: Pawl
JMJIA6153ZZ
: Pawl
JMJIA6154ZZ
JMJIA6155ZZ
INSTRUMENT PANEL ASSEMBLY
IP-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
c.
Remove glove box damper pin on right side.
CAUTION:
Never excessively pull string of glove box damper.
40. Remove instrument lower panel RH.
a.
Remove fixing screws (A).
b.
Pull back instrument lower panel RH, and then disengage pawls
and metal clips.
c.
Disconnect harness connectors and remove harness clips.
41. Disconnect passenger air bag module harness connector.
42. Remove passenger air bag module fixing bolt. Refer to
43. Remove cup holder assembly.
a.
Remove fixing screws (A).
b.
Pull back cup holder assembly.
: Clip
JMJIA6156ZZ
: Pawl
: Metal clip
JMJIA6157ZZ
JMJIA6158ZZ
IP-24
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
44. Remove instrument panel assembly.
a.
Remove harness clips from instrument panel assembly.
b.
Disengage harness (A), harness (B) and harness (D) of front pillar LH and RH portions from instrument
panel assembly.
c.
Disconnect harness connector (C).
Harness clip
JMJIA6159ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст