Nissan Quest E52. Instruction — part 924
PB-4
< PERIODIC MAINTENANCE >
PARKING BRAKE SYSTEM
c.
Adjust the parking brake pedal (1) stroke by turning the adjust-
ing nut (2) with a socket wrench.
CAUTION:
Never reuse the adjusting nut if the nut is removed.
d.
Operate the parking brake pedal with a force of 196 N (20 kg, 44
lb). Check that the pedal stroke is within the specified number of
notches. (Check it by listening to the clicks of the ratchet.)
e.
Rotate the disc rotor to check that there is no drag. Install the
plug. If any drag is found, follow the procedure described below.
i.
Adjust parking brake stroke again.
ii.
Check rear disc brake. Refer to
BR-50, "BRAKE CALIPER ASSEMBLY : Inspection"
.
Number of notches
: Refer to
JPFIB0044ZZ
PARKING BRAKE SHOE
PB-5
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SHOE
Adjustment
INFOID:0000000009651855
1.
Adjust parking brake pedal stroke. Refer to
PB-3, "Inspection and Adjustment"
2.
Perform parking brake break-in (drag on) operation by driving vehicle under the following conditions or
equivalency conditions:
• Drive forward
• Vehicle speed: Approx. 80 km/h (50 MPH) set (constant and forward)
• Parking brake operating force: 177.5 N (18.2 kg, 40.0 lb) set contact
• Time: Approx. 16 sec.
CAUTION:
• To prevent lining from getting too hot, allow a cool off period of approximately 5 minutes after
every break-in operation.
• Never perform excessive break-in operations, because doing so may cause uneven or early wear
of the lining.
3.
After the break-in procedure, check parking brake pedal stroke of parking brake.
CAUTION:
If it is out of the specification, adjust again. Refer to
PB-6
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Exploded View
INFOID:0000000009651856
Removal and Installation
INFOID:0000000009651857
REMOVAL
1.
Remove rear tires with power tool.
2.
Remove the instrument lower panel LH. Refer to
IP-14, "Removal and Installation"
.
3.
Disconnect the parking brake switch harness connector.
4.
Remove adjusting nut and loosen front cable.
5.
Remove the parking brake pedal assembly.
6.
Remove dash side finisher. Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installation"
.
7.
Remove front kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and Installation"
.
8.
Remove front seat (driver side).
• Instruction seat: Refer to
SE-88, "Removal and Installation"
.
SE-102, "Removal and Installation"
.
9.
Remove seat slide rail of second seat. Refer to
SE-114, "Removal and Installation"
1.
Parking brake switch
2.
Parking brake pedal assembly
3.
Return spring
4.
Stopper rubber
5.
Pedal pad
6.
Adjusting nut
7.
Front cable
8.
Spring
9.
Rear cable (LH)
10. Rear cable (RH)
11.
Pin
: Apply multi-purpose grease.
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSFIA0964GB
PARKING BRAKE CONTROL
PB-7
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
10. Remove floor carpet. Refer to
INT-30, "FRONT FLOOR CARPET : Removal and Installation"
11. Remove center muffler and heat plate. Refer to
EX-6, "Removal and Installation"
12. Separate front cable from rear cable, and remove front cable and spring.
13. Remove brake shoe. Refer to
14. Remove rear cable from toggle lever.
INSTALLATION
Note the following, install in the reverse order of the removal.
• Never reuse adjusting nut.
• Perform adjustment after installation. Refer to
PB-3, "Inspection and Adjustment"
Adjustment
INFOID:0000000009651858
ADJUSTMENT AFTER INSTALLATION
Adjust the parking brake pedal stroke. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст