Nissan Quest E52. Instruction — part 923
MWI
COMPASS
MWI-97
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
COMPASS
Exploded View
INFOID:0000000009651549
(with ADP), or
(without ADP).
Removal and Installation
INFOID:0000000009651550
MIR-29, "Removal and Installation"
(with ADP), or
MIR-48, "Removal and Installation"
(without ADP).
PB-1
BRAKES
C
D
E
G
H
I
J
K
L
M
SECTION
PB
A
B
PB
N
O
P
CONTENTS
PARKING BRAKE SYSTEM
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
PARKING BRAKE SYSTEM . . . . . . . ...
Inspection and Adjustment . . . . . . . . . ....
PARKING BRAKE SHOE . . . . . . . . ...
Adjustment . . . . . . . . . . . . . . . ....
REMOVAL AND INSTALLATION . . . .
PARKING BRAKE CONTROL . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Adjustment . . . . . . . . . . . . . . . ....
PARKING BRAKE SHOE . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection and Adjustment . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Parking Drum Brake . . . . . . . . . . . .
PB-2
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000009651853
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
PARKING BRAKE SYSTEM
PB-3
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PERIODIC MAINTENANCE
PARKING BRAKE SYSTEM
Inspection and Adjustment
INFOID:0000000009651854
INSPECTION
Pedal Stroke
1.
Operate the parking brake pedal with a force of 196 N (20 kg, 44 lb). Check that the pedal stroke is within
the specified number of notches. (Check it by listening to the clicks of the ratchet.)
2.
When brake warning lamp turns ON, check that the pedal stroke is within the specified number of
notches. (Check it by listening to the clicks of the ratchet.)
Inspect Components
• Check each component for installation condition such as looseness.
• Check the parking brake pedal assembly for bend, damage and cracks. Replace if necessary.
• Check the cables and equalizer for wear, damage and cracks. Replace if necessary.
• Check the parking brake switch, and replace it if necessary. Refer to
BRC-91, "Component Inspection"
ADJUSTMENT
1.
Remove rear tires with power tool.
2.
Fix the disc rotor using wheel nut.
3.
Remove fuse block lid. Refer to
IP-14, "Removal and Installation"
4.
Release the parking brake pedal (1) by turning the adjusting nut
(2) with a deep socket wrench and loosening the cable.
5.
Remove the adjusting hole plug from the disc rotor. Turn the
adjuster (1) in the direction (A) as shown in the figure using a
suitable tool until the disc rotor is locked.
6.
Turn back the adjuster 5 to 6 notches from the locked position.
7.
Rotate the disc rotor to check that there is no drag. Install the
adjuster hole plug. If any drag is found follow the procedure
described bellow.
a.
Adjust parking brake stroke again.
b.
Check rear disc brake. Refer to
8.
Adjust the cable with the following procedure.
a.
Temporarily adjust the cable so that the parking brake pedal operating force immediately before the full
stroke reaches 490 N (50 kg, 110 lb) or more.
b.
Operate the parking brake pedal with a force of 490 N (50 kg, 110 lb) for 10 strokes or more.
Number of notches
: Refer to
PB-11, "Parking Brake Control"
Number of notches
: Refer to
PB-11, "Parking Brake Control"
JPFIB0044ZZ
JPFIB0002ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст