Nissan Quest E52. Instruction — part 438
DLK-466
< REMOVAL AND INSTALLATION >
SLIDE DOOR LOCK
SLIDE DOOR LOCK
Exploded View
INFOID:0000000009649473
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
1.
Outside handle assembly
2.
Outside handle escutcheon
3.
TORX bolt
4.
Snap pin
5.
Inside handle
6.
Remote control door lock cable
7.
Slide door lock assembly (front)
8.
Slide door lock cover (front)
9.
Slide door lock release actuator
10. Cable clip
11. Slide door lock assembly (rear)
12. Slide door lock cover (rear)
13. Slide door lock cable (rear)
14. Outside handle bracket
15. Rear gasket
16. Front gasket
17. Slide door lock actuator
18. Clip
19. Remote control assembly
20. Lock knob
21
Outside handle cable
22. Slide door lock cable (front)
23. Slide door closure motor
24. Automatic sliding door unit
A
: To lower latch
: Clip
: Vehicle front
: N·m (kg-m, in-lb)
: Body grease
JMKIA8653GB
SLIDE DOOR LOCK
DLK-467
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• During removal and installation, work so as not to bend the ends of the cable.
• After installation, check door open/close, lock/unlock operation.
• Check door lock assembly for poor lubrication. Apply body grease to door lock if necessary.
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009649474
SLIDE DOOR LOCK ASSEMBLY (FRONT)
Removal
1.
Fully close the slide door glass.
2.
Remove remote control assembly. Refer to
DLK-473, "REMOTE CONTROL ASSEMBLY : Removal and
.
3.
Remove lock release actuator. Refer to
DLK-474, "LOCK RELEASE ACTUATOR : Removal and Installa-
4.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
5.
Remove cable fixing clip (A) of slide door lock cable (1).
6.
Remove mounting bolt, and then remove slide door lock assembly (front) and slide door lock cable (front)
as a set.
7.
Disconnect slide door lock cable (front) from slide door lock assembly (front).
a.
Remove fixing screw, and then remove slide door lock cover (front)
b.
Open cable mounting clip (A) of slide door lock assembly (front)
(1).
c.
Disconnect slide door lock cable (front) (2).
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Always adjust cable when assembling slide door lock cable (front) to slide door lock assembly
(front). Refer to
DLK-469, "DOOR LOCK : Inspection and Adjustment"
.
• After installation, check door open/close, lock/unlock operation.
SLIDE DOOR LOCK ASSEMBLY (REAR)
Removal
1.
Fully close the slide door glass.
: Vehicle front
JMKIA6297ZZ
: Vehicle front
JMKIA6298ZZ
DLK-468
< REMOVAL AND INSTALLATION >
SLIDE DOOR LOCK
2.
Remove remote control assembly. Refer to
DLK-473, "REMOTE CONTROL ASSEMBLY : Removal and
.
3.
Remove lock release actuator. Refer to
DLK-474, "LOCK RELEASE ACTUATOR : Removal and Installa-
4.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
5.
Remove harness connector fixing clip (A), and then disconnect
slide door lock assembly harness connector (1).
6.
Remove cable fixing clip (A)
7.
Disengage slide door lock cable (rear) (1) from cable clip (B).
8.
Remove door lower sash (rear) of slide door glass. Refer to
.
9.
Remove mounting bolt, and then remove slide door lock assembly (rear) and slide door lock cable (rear)
as a set.
a.
Remove slide door lock (rear) mounting bolts.
b.
Remove slide door lock (rear) (2) from reinforcement (1) of slide door panel
10. Disconnect slide door lock cable (rear) from slide door lock assembly (rear).
a.
Remove fixing screw, and then remove slide door lock cover (rear)
: Vehicle front
JMKIA6299ZZ
: Vehicle front
JMKIA6300ZZ
: Vehicle front
JMKIA6301ZZ
SLIDE DOOR LOCK
DLK-469
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
b.
Open cable mounting clip (A) of slide door lock assembly (rear)
(1).
c.
Disconnect slide door lock cable (rear) (2).
11. Remove slide door closure motor from slide door lock assembly (rear).
a.
Disconnect harness connector of slide door closure motor.
b.
Remove mounting molts, and then slide door closure motor.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Always adjust cable when assembling slide door lock cable (rear) to slide door lock assembly (rear).
Refer to
DLK-469, "DOOR LOCK : Inspection and Adjustment"
.
• After installation, check door open/close, lock/unlock operation.
DOOR LOCK : Inspection and Adjustment
INFOID:0000000009649475
ADJUSTMENT OF SLIDE DOOR LOCK CABLE (FRONT)
1.
Temporarily install slide door lock cable (front) to slide door lock assembly (front).
2.
Set claw (1) of slide door lock assembly (front) to full latch sta-
tus. (Press until it clicks.)
3.
Pull lightly inner cable (1) of remote control assembly side in the direction indicated by arrow as shown in
the figure so that play is eliminated. With play eliminated, adjust projection (A) by moving inner cable (2) of
slide door lock assembly (front) side.
: Vehicle front
JMKIA6298ZZ
JMKIA6303ZZ
A
: 45.8 – 47.2 mm (1.803 – 1.852 in)
JMKIA6304ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст