Nissan Quest E52. Instruction — part 437
DLK-462
< REMOVAL AND INSTALLATION >
HOOD LOCK
5.
Check the hood lock lubrication condition. If necessary, apply
body grease to hood lock.
: Grease up point
JMKIA5674ZZ
FRONT DOOR LOCK
DLK-463
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR LOCK
Exploded View
INFOID:0000000009649469
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009649470
REMOVAL
1.
Remove outside handle and outside handle bracket. Refer to
DLK-464, "OUTSIDE HANDLE : Removal
2.
Disconnect door lock actuator connector.
3.
Remove door lock assembly TORX bolts, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
1.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
2.
Rear gasket
3.
TORX bolt
4.
Key rod (driver side)
5.
Door lock assembly
6.
Inside handle cap
7.
Inside handle
8.
Front gasket
9.
Outside handle
10. Outside handle bracket
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIA8259GB
DLK-464
< REMOVAL AND INSTALLATION >
FRONT DOOR LOCK
• Check door open/close, lock/unlock operation after installation.
• Check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009649471
REMOVAL
1.
Remove front door finisher. Refer to
INT-14, "Removal and Installation"
2.
Remove inside handle mounting screws, and then remove the inside handle.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check door lock cables are properly engaged with inside handle.
• After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009649472
REMOVAL
1.
Remove module base. Refer to
GW-29, "Removal and Installation"
2.
Disconnect key rod from door lock assembly (driver side).
3.
Remove door antenna harness connector fixing clip (1), and
then disconnect harness connector (2).
4.
Remove grommet (1) of door side. Loosen, through grommet
hole, TORX bolt (2) that fixes door lock cylinder. (For passenger
side, TORX bolt fixes outside handle escutcheon.)
: Grease up point
JMKIA5892ZZ
: Vehicle front
JMKIA8260ZZ
JMKIA5888ZZ
FRONT DOOR LOCK
DLK-465
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
While pulling outside handle, remove door key cylinder assem-
bly (driver side) or outside handle escutcheon (passenger side).
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7.
Remove front gasket and rear gasket.
8.
Peel hole cover (1) carefully, and then remove TORX bolt (2),
which is fixing outside handle bracket, through hole.
CAUTION:
When affixing hole cover, if affixing force is insufficient,
replace hole cover.
9.
Slide outside handle bracket toward front of vehicle to remove.
10. Disconnect outside handle cable from outside handle bracket.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt.
• Check door lock cable is properly engaged with outside handle bracket.
• After installation, check door open/close, lock/unlock operation.
JMKIA0560ZZ
JMKIA0524ZZ
JMKIA8261ZZ
PIIB5815E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст