Nissan Quest E52. Instruction — part 1036
FRONT LOWER LINK
RSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
FRONT LOWER LINK
Exploded View
INFOID:0000000009652832
Removal and Installation
INFOID:0000000009652833
REMOVAL
1.
Remove tire with power tool. Refer to
.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-120, "REAR WHEEL SENSOR : Removal and
.
3.
Remove rear lower link and coil spring. Refer to
RSU-8, "Removal and Installation"
4.
Separate shock absorber from front lower link. Refer to
5.
Remove eccentric disc, adjusting bolt, mounting bolt, and nut, then remove front lower link.
6.
Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install adjusting bolt so that the graduation marks on adjusting bolt are positioned downward.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Never reuse front lower link mounting nut.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000009652834
INSPECTION AFTER REMOVAL
Check front lower link and bushing for any deformation, cracks, or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
1.
Rear suspension member
2.
Radius rod
3.
Adjusting bolt
4.
Front lower link
5.
Eccentric disk
6.
Rear lower link
7.
Rubber seat
8.
Coil spring
9.
Upper seat
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSEIA0397GB
RSU-16
< REMOVAL AND INSTALLATION >
FRONT LOWER LINK
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
(with VDC).
SUSPENSION ARM
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SUSPENSION ARM
Exploded View
INFOID:0000000009652835
Removal and Installation
INFOID:0000000009652836
REMOVAL
1.
Remove tires with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-120, "REAR WHEEL SENSOR : Removal and
.
3.
Separate suspension arm from front lower link. Refer to
RAX-6, "Removal and Installation"
4.
Remove mounting bolt, and nut, then remove stopper rubber and suspension arm.
5.
Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install stopper rubber to rear suspension member together with suspension arm.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Never reuse suspension arm mounting nut.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000009652837
INSPECTION AFTER REMOVAL
Check the following items, and replace the parts if necessary.
Suspension Arm
• Suspension arm and bushing for deformation, cracks or damage.
• Ball joint boot for cracks or other damage, and also for grease leakage.
Swing Torque
1.
Instructionly move ball stud to confirm it moves smoothly with no binding.
2.
Move ball stud at least ten times by hand to check for smooth movement.
1.
Rear suspension member
2.
Stopper rubber
3.
Suspension arm
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSEIA0398GB
RSU-18
< REMOVAL AND INSTALLATION >
SUSPENSION ARM
3.
Hook spring balance (A) at cotter pin mounting hole. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
• If swing torque exceeds standard range, replace suspension arm
assembly.
Axial End Play
1.
Instructionly move ball stud to confirm it moves smoothly with no binding.
2.
Move ball stud at least ten times by hand to check for smooth movement.
3.
Move tip of ball stud in axial direction to check for looseness.
• If axial end play exceeds the standard value, replace suspension arm assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
(with VDC).
Swing torque
: Refer to
.
JPEIA0005ZZ
Axial end play
: Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст