Nissan Quest E52. Instruction — part 1027
GLASS LID
RF-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
REAR SUNROOF : Removal and Installation
INFOID:0000000009650390
REMOVAL
1.
Tilt up glass lid and remove side trims (LH and RH).
2.
Remove glass lid mounting TORX bolts, and then remove glass lid from vehicle.
3.
Fully close glass lid.
INSTALLAITON
Note the following items, and then install in the reverse order of removal.
NOTE:
After installation carry out fitting adjustment. Refer to
RF-51, "REAR SUNROOF : Adjustment"
REAR SUNROOF : Adjustment
INFOID:0000000009650391
Adjustment
If the clearance and the surface height are out of specification, adjust them according to the procedures shown below.
1.
Tilt up glass lid and remove side trims (LH and RH).
2.
Loosen glass lid mounting TORX bolts.
3.
Adjust the clearance of glass lid and roof panel according to the fitting standard dimension.
1.
Roof panel
2.
Glass lid
JMKIA6147ZZ
RF-52
< REMOVAL AND INSTALLATION >
GLASS LID
4.
To prevent glass lid from moving after adjustment, first tighten the TORX bolts of front left, and then
tighten the TORX bolts of rear right.
5.
Tilt glass lid up and down several times to check that it moves smoothly.
NOTE:
After adjustment the sunroof unit assembly, perform additional service. Refer to
.
Portion
a (Clearance)
b (Surface height difference)
A – A
6.5 – 8.1 mm
(0.256 – 0.319 in)
(
−
2.3) – (+0.7) mm
[(
−
0.091) – (+0.028) in]
B – B
6.5 – 8.1 mm
(0.256 – 0.319 in)
(
−
2.3) – (+0.7) mm
[(
−
0.091) – (+0.028) in]
C – C
6.5 – 8.1 mm
(0.256 – 0.319 in)
(
−
2.3) – (+0.7) mm
[(
−
0.091) – (+0.028) in]
SUNROOF MOTOR ASSEMBLY
RF-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNROOF MOTOR ASSEMBLY
FRONT SUNROOF
FRONT SUNROOF : Exploded View
INFOID:0000000009650392
FRONT SUNROOF : Removal and Installation
INFOID:0000000009650393
REMOVAL
CAUTION:
• Before removing sunroof motor, check that glass lid is fully closed.
1.
Glass lid
2.
TORX bolt
3.
Front sunroof bracket
4.
Center drain hose
5.
Side trim
6.
Front drain hose
7.
Front drain connector
8.
Sunroof motor assembly
9.
Sunroof unit assembly
: Metal clip
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA6143ZZ
RF-54
< REMOVAL AND INSTALLATION >
SUNROOF MOTOR ASSEMBLY
• After removing sunroof motor, never attempt to rotate sunroof motor assembly as a single unit.
1.
Fully close glass lid.
2.
Remove map lamp assembly. Refer to
INL-67, "Removal and Installation"
3.
Remove sunroof motor assembly fixing screws (A), and then
remove sunroof motor assembly.
4.
Disconnect harness connector from sunroof motor.
INSTALLAITON
1.
Move the sunroof motor assembly laterally by little so that the gear is completely engaged into the wire on
the sunroof unit assembly and mounting surface becomes parallel. Then secure the sunroof motor
assembly with screws.
2.
Install map lamp assembly. Refer to
INL-67, "Removal and Installation"
.
NOTE:
After installation sunroof motor, perform additional service. Refer to
RF-21, "FRONT SUNROOF : Descrip-
.
REAR SUNROOF
JMKIA6151ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст