Nissan Quest E52. Instruction — part 1231
TM-154
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
CVT SHIFT SELECTOR
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded View
INFOID:0000000009650222
Removal and Installation
INFOID:0000000009650223
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1.
Disconnect the battery cable from the negative terminal. Refer to
PG-105, "Removal and Installation"
2.
Move selector lever to “N” position.
CAUTION:
When pushing shift lock release button, warp waste around the tip of flat screw driver to prevent
damage.
3.
Slide knob cover (1) below selector lever downward.
CAUTION:
Be careful not to damage knob cover.
4.
Pull lock pin (2) out of selector lever knob (3).
5.
Remove selector lever knob and knob cover.
6.
Remove cluster lid C. Refer to
IP-14, "Removal and Installation"
.
7.
Disconnect CVT shift selector connector.
1.
Selector lever knob
2.
Lock pin
3.
Knob cover
4.
Slide plate
5.
Shift lock solenoid
6.
CVT shift selector assembly
: N·m (kg-m, in-lb)
JPDIA1209GB
JPDIA1211ZZ
CVT SHIFT SELECTOR
TM-155
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8.
Remove control cable (1) from CVT shift selector assembly (2).
9.
Remove CVT shift selector assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing control cable (1) to CVT shift selector assembly
(2), check that control cable is fully pressed in with the ribbed (A)
surface facing rearward.
• Refer to the followings when installing the selector lever knob to the CVT shift selector assembly.
1.
Install the lock pin (2) to the selector lever knob (3).
2.
Install the knob cover (1) to the selector lever knob.
3.
Insert the selector lever knob into the CVT shift selector assem-
bly until it clicks.
CAUTION:
• When pressing the selector lever knob onto the selector
lever, never press the selector lever knob button.
• Never strike the selector lever knob to press it into place.
4.
After installing the selector lever knob to the CVT shift selector
assembly, check that the pulling on the selector lever knob does
not disconnect it.
Disassembly and Assembly
INFOID:0000000009650224
Disassembly
1.
Remove slide plate from cluster lid C.
2.
Disconnect the shift lock solenoid connector.
3.
Remove shift lock solenoid from CVT shift selector assembly.
Assembly
Assembly in the reverse order of disassembly.
Inspection and Adjustment
INFOID:0000000009650225
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing CVT shift selector assembly. Refer to
TM-70, "Inspection and Adjust-
INSPECTION AFTER INSTALLATION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-70, "Inspection and Adjustment"
.
A
: The ribbed
JPDIA1210ZZ
JPDIA1210ZZ
JPDIA1211ZZ
TM-156
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
CONTROL CABLE
CONTROL CABLE
Exploded View
INFOID:0000000009650226
Removal and Installation
INFOID:0000000009650227
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1.
Disconnect the battery cable from the negative terminal. Refer to
PG-105, "Removal and Installation"
2.
Remove control cable from CVT shift selector assembly. Refer to
TM-154, "Removal and Installation"
3.
Remove air duct (inlet) and air cleaner case. Refer to
EM-26, "Removal and Installation"
.
4.
Remove the control cable installation nut from the instruction lever.
1.
CVT shift selector assembly
2.
Control cable
3.
Lock plate
4.
Bracket
5.
Transaxle assembly
A.
Instruction lever
B.
Retainer
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPDIA1212GB
CONTROL CABLE
TM-157
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5.
Remove lock plate (1) from control cable.
6.
Remove instrument lower cover center. Refer to
7.
Remove bolts (
) of retainer (A).
8.
Remove the control cable from the vehicle.
9.
Remove bracket from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing control cable (1) to CVT shift selector assembly
(2), check that control cable is fully pressed in with the ribbed (A)
surface facing rearward.
• Install the socket (A) onto the CVT shift selector assembly.
CAUTION:
• Place the socket onto the CVT shift lever, then fasten it in
place from above.
• Check that the pulling on the socket does not disconnect it.
Inspection and Adjustment
INFOID:0000000009650228
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing control cable. Refer to
TM-70, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLATION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-70, "Inspection and Adjustment"
.
JSDIA1812ZZ
JSDIA2329ZZ
JPDIA1210ZZ
JSDIA2320ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст