Nissan Quest E52. Instruction — part 1232
TM-158
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
TCM
TCM
Exploded View
INFOID:0000000009650229
Removal and Installation
INFOID:0000000009650230
REMOVAL
CAUTION:
• When replacing TCM and transaxle assembly as a set, replace transaxle assembly first and then
replace TCM. Refer to
.
• Never impact on TCM when removing or installing TCM.
1.
Disconnect the battery cable from the negative terminal. Refer to
PG-105, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-26, "Removal and Installation"
3.
Move battery harness to a place to keep the harness clear of working area.
4.
Disconnect TCM connector.
5.
Remove TCM.
INSTALLATION
Install in the reverse order of removal.
Adjustment
INFOID:0000000009650231
ADJUSTMENT AFTER INSTALLATION
Perform “ADDITIONAL SERVICE WHEN REPLACING TCM”. Refer to
1.
TCM
: N·m (kg-m, in-lb)
JPDIA0870GB
AIR BREATHER HOSE
TM-159
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Exploded View
INFOID:0000000009650232
Removal and Installation
INFOID:0000000009650233
REMOVAL
1.
Disconnect the battery cable from the negative terminal. Refer to
PG-105, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-26, "Removal and Installation"
3.
Remove clip from air cleaner case.
4.
Remove air cleaner case and air duct assembly. Refer to
EM-26, "Removal and Installation"
.
5.
Remove clip from heater pipe.
6.
Remove air breather hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
1.
Air cleaner case
2.
Air breather hose
3.
Transaxle assembly
4.
Heater pipe
: Vehicle front
JPDIA0592ZZ
TM-160
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
AIR BREATHER HOSE
• Insert air breather hose (2) to the bend (A) of air breather tube
(1).
• Install air breather hose to air breather tube so that the paint
mark is facing forward.
• Check that air breather hose is not collapsed or blocked due
to folding or bending when installed.
JPDIA0872ZZ
SECONDARY SPEED SENSOR
TM-161
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SECONDARY SPEED SENSOR
Exploded View
INFOID:0000000009650234
Removal and Installation
INFOID:0000000009650235
REMOVAL
1.
Remove the battery. Refer to
PG-105, "Removal and Installation"
.
2.
Remove ECM and bracket. Refer to
EC-460, "Removal and Installation"
3.
Remove air duct (inlet), air duct assembly, and air cleaner case. Refer to
4.
Disconnect secondary speed sensor connector.
5.
Remove secondary speed sensor.
6.
Remove O-ring from secondary speed sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000009650236
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
1.
Secondary speed sensor
2.
O-ring
3.
Transaxle assembly
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Apply CVT fluid
JSDIA4983GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст