Nissan Quest E52. Instruction — part 405
DLK-334
< DTC/CIRCUIT DIAGNOSIS >
SLIDING DOOR LOCK STATUS SWITCH
SLIDING DOOR LOCK STATUS SWITCH
SLIDING DOOR LH
SLIDING DOOR LH : Component Function Check
INFOID:0000000009649274
1.
CHECK FUNCTION
1.
Select “AUTO SLDE DOOR” using CONSULT.
2.
Select “KNOB LCK SW L” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Sliding door lock status switch is OK.
NO
>> Refer to
DLK-334, "SLIDING DOOR LH : Diagnosis Procedure"
SLIDING DOOR LH : Diagnosis Procedure
INFOID:0000000009649275
1.
CHECK SLIDING DOOR LOCK STATUS SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding door lock status switch LH connector.
3.
Check voltage between sliding door lock status switch LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR LOCK STATUS SWITCH CIRCUIT
1.
Disconnect sliding door control unit LH connector.
2.
Check continuity between sliding door control unit LH harness connector and sliding door lock status
switch LH harness connector.
3.
Check continuity between sliding door control unit LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door control unit LH. Refer to
DLK-500, "LH : Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR LOCK STATUS SWITCH GROUND CIRCUIT
1.
Disconnect sliding door control unit LH connector.
2.
Check continuity between sliding door control unit LH harness connector and sliding door lock status
switch LH harness connector.
Monitor item
Condition
Status
KNOB LCK SW L
Sliding door LH
LOCK
OFF
UNLOCK
ON
(+)
(–)
Voltage
Sliding door lock status switch LH
Connector
Terminal
D119
1
Ground
8 – 16 V
Sliding door control unit LH
Sliding door lock status switch LH
Continuity
Connector
Terminal
Connector
Terminal
B45
3
D119
1
Existed
Sliding door control unit LH
Ground
Continuity
Connector
Terminal
B45
3
Not existed
SLIDING DOOR LOCK STATUS SWITCH
DLK-335
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between sliding door control unit LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SLIDING DOOR LOCK STATUS SWITCH CIRCUIT 2
1.
Connect sliding door control unit LH connector and sliding door lock status switch LH connector.
2.
Check voltage between sliding door control unit LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace sliding door control unit LH. Refer to
DLK-500, "LH : Removal and Installation"
5.
CHECK SLIDING DOOR LOCK STATUS SWITCH
DLK-331, "SLIDING DOOR LH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace sliding door lock actuator LH.
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
SLIDING DOOR LH : Component Inspection
INFOID:0000000009649276
1.
CHECK SLIDING DOOR LOCK STATUS SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sliding door lock status switch LH connector.
3.
Check continuity between sliding door lock status switch LH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sliding door lock status switch LH.
SLIDING DOOR RH
Sliding door control unit LH
Sliding door lock status switch LH
Continuity
Connector
Terminal
Connector
Terminal
B45
23
D119
3
Existed
Sliding door control unit LH
Ground
Continuity
Connector
Terminal
B45
23
Not existed
(+)
(–)
Voltage
Sliding door control unit LH
Connector
Terminal
B45
23
Ground
0 V
Sliding door lock status switch LH
Condition
Continuity
Terminal
3
1
Sliding door LH
LOCK
Not existed
UNLOCK
Existed
DLK-336
< DTC/CIRCUIT DIAGNOSIS >
SLIDING DOOR LOCK STATUS SWITCH
SLIDING DOOR RH : Component Function Check
INFOID:0000000009649277
1.
CHECK FUNCTION
1.
Select “AUTO SLDE DOOR RIGHT” using CONSULT.
2.
Select “KNOB LCK SW R” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Sliding door lock status switch is OK.
NO
>> Refer to
DLK-332, "SLIDING DOOR RH : Diagnosis Procedure"
SLIDING DOOR RH : Diagnosis Procedure
INFOID:0000000009649278
1.
CHECK SLIDING DOOR LOCK STATUS SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding door lock status switch RH connector.
3.
Check voltage between sliding door lock status switch RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR LOCK STATUS SWITCH CIRCUIT
1.
Disconnect sliding door control unit RH connector.
2.
Check continuity between sliding door control unit RH harness connector and sliding door lock status
switch RH harness connector.
3.
Check continuity between sliding door control unit RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door control unit RH. Refer to
DLK-500, "RH : Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR LOCK STATUS SWITCH GROUND CIRCUIT
1.
Disconnect sliding door control unit RH connector.
2.
Check continuity between sliding door control unit RH harness connector and sliding door lock status
switch RH harness connector.
Monitor item
Condition
Status
KNOB LCK SW R
Sliding door RH
LOCK
OFF
UNLOCK
ON
(+)
(–)
Voltage
Sliding door lock status switch RH
Connector
Terminal
D120
3
Ground
8 – 16 V
Sliding door control unit RH
Sliding door lock status switch RH
Continuity
Connector
Terminal
Connector
Terminal
B247
3
D120
3
Existed
Sliding door control unit RH
Ground
Continuity
Connector
Terminal
B247
3
Not existed
SLIDING DOOR LOCK STATUS SWITCH
DLK-337
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between sliding door control unit RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SLIDING DOOR LOCK STATUS SWITCH CIRCUIT 2
1.
Connect sliding door control unit RH connector and sliding door lock status switch RH connector.
2.
Check voltage between sliding door control unit RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace sliding door control unit RH. Refer to
DLK-500, "RH : Removal and Installation"
5.
CHECK SLIDING DOOR LOCK STATUS SWITCH
DLK-333, "SLIDING DOOR RH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace sliding door lock actuator RH.
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
SLIDING DOOR RH : Component Inspection
INFOID:0000000009649279
1.
CHECK SLIDING DOOR LOCK STATUS SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sliding door lock status switch RH connector.
3.
Check continuity between sliding door lock status switch RH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sliding door lock actuator RH.
Sliding door control unit RH
Sliding door lock status switch RH
Continuity
Connector
Terminal
Connector
Terminal
B247
23
D120
1
Existed
Sliding door control unit RH
Ground
Continuity
Connector
Terminal
B247
23
Not existed
(+)
(–)
Voltage
Sliding door control unit RH
Connector
Terminal
B247
23
Ground
0 V
Sliding door lock status switch RH
Condition
Continuity
Terminal
3
1
Sliding door RH
LOCK
Not existed
UNLOCK
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст