Nissan Quest E52. Instruction — part 1283
WASHER NOZZLE & TUBE
WW-65
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Hydraulic Layout
INFOID:0000000009649587
WASHER NOZZLE
WASHER NOZZLE : Removal and Installation
INFOID:0000000009649588
FRONT WASHER NOZZLE
REMOVAL
1.
Remove cowl top cover. Refer to
EXT-22, "Removal and Installation"
.
2.
Disconnect front washer tube (3) from the front washer nozzle
(1).
3.
Press front washer nozzle fixing pawls toward the direction
shown by the arrows 2 and pull up remove from cowl top cover
(2).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
1.
Grommet A
2.
Rear washer tube
3.
Washer tank assembly
4.
Front washer tube
5.
Front washer nozzle
6.
Rear washer nozzle
7.
Grommet B
8.
Back door seal rubber
: Clip
JMLIA2135ZZ
JMLIA1537ZZ
WW-66
< REMOVAL AND INSTALLATION >
WASHER NOZZLE & TUBE
CAUTION:
• The spray positions differ, check that left and right nozzles are installed correctly.
• Adjust the washer nozzle spray position. Refer to
WW-66, "WASHER NOZZLE : Inspection and
REAR WASHER NOZZLE
REMOVAL
1.
Remove rear spoiler. Refer to
EXT-45, "Removal and Installation"
.
2.
Remove high-mounted stop lamp.
• Xenon type: Refer to
EXL-117, "Removal and Installation"
• Halogen type: Refer to
EXL-226, "Removal and Installation"
3.
Press rear washer nozzle fixing pawls (A) toward the direction
shown by the arrows and remove from rear spoiler (1).
4.
Disconnect front washer tube from the front washer nozzle.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
Adjust the washer nozzle spray position. Refer to
WW-66, "WASHER NOZZLE : Inspection and Adjust-
.
WASHER NOZZLE : Inspection and Adjustment
INFOID:0000000009649589
INSPECTION
FRONT CHECK VALVE INSPECTION
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
REAR CHECK VALVE INSPECTION
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
JMLIA2161ZZ
JMLIA1538ZZ
JMLIA2159ZZ
WASHER NOZZLE & TUBE
WW-67
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
ADJUSTMENT
FRONT WASHER NOZZLE SPRAY POSITION ADJUSTMENT
Adjust spray positions to match the positions shown in the figure.
Unit: mm (in)
Check that washer fluid is splayed on 70% or more the splay area (
) when spraying washer fluid. If the
spray area deviates from the specification, adjust the washer nozzle.
CAUTION:
• Use washer nozzle adjuster (A) for nozzle (1) insert adjust-
ment if the jet a is outside the angle.
• Never use needle or small pin.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle or small pin.
REAR WASHER NOZZLE SPRAY POSITION ADJUSTMENT
Adjust spray positions to match the positions shown in the figure.
: Spray area
1.
Black printed frame line
Driver side
Passenger side
A
B
C
D
E
F
G
H
X
578 (22.76)
381 (15.00)
181 (7.13)
129 (5.08)
88 (3.46)
169 (6.65)
366 (14.41)
484 (19.06)
Y
638 (14.49)
62 (2.44)
56 (2.20)
703 (27.68)
674 (26.54)
49 (1.93)
61 (2.40)
504 (19.84)
JMLIA2065ZZ
JMLIA1539ZZ
WW-68
< REMOVAL AND INSTALLATION >
WASHER NOZZLE & TUBE
Unit: mm (in)
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle or small pin.
WASHER TUBE
WASHER TUBE : Removal and Installation
INFOID:0000000009649590
FRONT WASHER TUBE
REMOVAL
1.
Fully open hood assembly.
2.
Remove fender protector RH (front). Refer to
EXT-23, "Removal and Installation"
3.
Disconnect front washer tub A from the front & rear washer pump.
1.
Rear washer nozzle
2.
Black print frame line
H : Height
L : Length
φ
: Spray position area
3.0 (0.118)
115.0 (4.528)
30 (1.181)
JMLIA2155ZZ
JMLIA2160ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст