Nissan Quest E52. Instruction — part 430
DLK-434
< REMOVAL AND INSTALLATION >
FRONT DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000009649432
Check the clearance and the surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Front fender
2.
Front door
3.
Slide door
4.
Front door hinge (upper)
5.
Front door hinge (lower)
6.
Door striker
7.
TORX bolt
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Front fender – Front door
A – A
Clearance
3.5 – 5.5 mm (0.138 – 0.217 in)
Surface height
(
−
1.0) – (+1.0) mm [(
−
0.039) –
(+0.039) in]
JMKIA8257GB
FRONT DOOR
DLK-435
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FITTING ADJUSTMENT PROCEDURE
1.
Remove front fender. Refer to
DLK-430, "FRONT FENDER : Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
8.
Install front fender. Refer to refer to
DLK-430, "FRONT FENDER : Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000009649433
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check front door open/close, operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000009649434
REMOVAL
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
1.
Remove front fender. Refer to
DLK-430, "FRONT FENDER : Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-432, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts (body side), and then remove front door hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
Front door – Slide door
B – B
Clearance
3.5 – 5.5 mm (0.138 – 0.217 in)
Surface height
(
−
1.0) – (+1.0) mm [(
−
0.039) –
(+0.039) in]
Portion
Standard
DLK-436
< REMOVAL AND INSTALLATION >
FRONT DOOR
• After installation, perform the fitting adjustment. Refer to
DLK-434, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• Check door hinge rotating part for poor lubrication. If neces-
sary, apply body grease.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000009649435
REMOVAL
1.
Fully close the front door window.
2.
Remove front door finisher. Refer to
INT-14, "Removal and Installation"
3.
Remove bracket mounting bolts of front door speaker.
4.
Remove front door speaker and bracket as a set, and move them aside.
5.
Remove mounting bolt of door check link on the vehicle.
6.
Remove mounting nuts of door check link on door panel.
7.
Take door check link (1) out from the hole of door panel (2).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close operation after installation.
• Check door check link rotating part for poor lubrication. If
necessary, apply grease.
: Grease up point
JMKIA5641ZZ
JMKIA8258ZZ
: Grease up point
JMKIA5642ZZ
SLIDE DOOR
DLK-437
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SLIDE DOOR
Exploded View
INFOID:0000000009649436
1.
Slide door panel
2.
Bumper rubber
3.
Grommet
4.
TORX bolt
5.
Door striker (front)
6.
Touch sensor (automatic sliding door
models)
7.
Dovetail (female)
8.
Dovetail (male)
9.
Lower latch
10. Lower roller
11. Slide door lower stopper
12. Slide door lower striker
13. Slide door lower weather-strip
14. Screw grommet
15. Rear roller
16. Roller
17. TORX bolt
18. Slide door outside protector
19. Door striker (rear)
20. Stopper rubber
21. Upper roller assembly
22. Sub roller
23. Slide door upper stopper
A
: To slide door lower rail
B
: To body outer panel
C
: Slide door upper rail
JMKIA6197GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст