Nissan Cube. Instruction — part 108
BRC-82
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
VDC OFF SWITCH
Component Inspection
INFOID:0000000009950007
1.
CHECK VDC OFF SWITCH
1.
Turn the ignition switch OFF.
2.
Disconnect VDC OFF switch harness connector.
3.
Check the continuity between VDC OFF switch harness connector.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace VDC OFF switch. Refer to
BRC-117, "Removal and Installation"
.
Special Repair Requirement
INFOID:0000000009950008
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit) or steering angle sensor and removing steering angle sensor. Refer to
9, "Special Repair Requirement"
>> END
VDC OFF switch
Condition
Continuity
Terminal
1
−
2
When VDC OFF switch is hold pressed.
Existed
When releasing VDC OFF switch.
Not existed
ABS WARNING LAMP
BRC-83
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ABS WARNING LAMP
Description
INFOID:0000000009950009
×
: ON –: OFF
Component Function Check
INFOID:0000000009950010
1.
CHECK ABS WARNING LAMP OPERATION
Check that the lamp illuminates for approximately 1 second after the ignition switch is turned ON.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to diagnosis procedure. Refer to
.
Diagnosis Procedure
INFOID:0000000009950011
1.
PERFORM SELF-DIAGNOSIS
Perform self-diagnosis for “ABS” with CONSULT.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check item displayed by self-diagnosis.
2.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
.
NO
>> Repair or replace error-detected parts.
Special Repair Requirement
INFOID:0000000009950012
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit) or steering angle sensor and removing steering angle sensor. Refer to
9, "Special Repair Requirement"
>> END
Condition
ABS warning lamp
Ignition switch OFF
–
For 1 second after turning ignition switch ON
×
1 second later after turning ignition switch ON
–
ABS function is malfunctioning.
×
EBD function is malfunctioning.
×
BRC-84
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
BRAKE WARNING LAMP
BRAKE WARNING LAMP
Description
INFOID:0000000009950013
×
: ON –: OFF
NOTE:
• 1: Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid level switch operation
(when brake fluid is insufficient).
• 2: After starting the engine, brake warning lamp is turned off.
Component Function Check
INFOID:0000000009950014
1.
BRAKE WARNING LAMP OPERATION CHECK 1
Check that the lamp illuminates for approximately 1 second after the ignition switch is turned ON.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Proceed to diagnosis procedure. Refer to
.
2.
BRAKE WARNING LAMP OPERATION CHECK 2
Check that the brake warning lamp in the combination meter turns ON/OFF correctly when operating the park-
ing brake pedal.
NOTE:
Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid level
switch operation (when brake fluid is insufficient).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check parking brake switch. Refer to
BRC-79, "Component Inspection"
Diagnosis Procedure
INFOID:0000000009950015
1.
PERFORM SELF-DIAGNOSIS
Perform self-diagnosis for “ABS” with CONSULT.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check item displayed by self-diagnosis.
2.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
.
NO
>> Repair or replace error-detected parts.
Special Repair Requirement
INFOID:0000000009950016
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Condition
Brake warning lamp (Note 1)
Ignition switch OFF
–
For 1 second after turning ignition switch ON
×
(Note 2)
1 second later after turning ignition switch ON
×
(Note 2)
ABS function is malfunctioning.
–
EBD function is malfunctioning.
×
BRAKE WARNING LAMP
BRC-85
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit) or steering angle sensor and removing steering angle sensor. Refer to
9, "Special Repair Requirement"
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст