Nissan Cube. Instruction — part 494
FAX-12
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT BOOT
WHEEL SIDE
WHEEL SIDE : Removal and Installation
INFOID:0000000009948795
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-110, "FRONT WHEEL SENSOR : Exploded
.
3.
Remove lock plate from strut assembly. Refer to
BR-20, "FRONT : Exploded View"
.
4.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Exploded View"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
BR-35, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
6.
Remove cotter pin, and then loosen wheel hub lock nut. Refer to
.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.
8.
Remove wheel hub lock nut.
9.
Remove strut assembly from steering knuckle. Refer to
.
10. Remove drive shaft from wheel hub and bearing assembly.
11. Remove boot bands, and then remove boot from joint subassembly.
12. Screw drive shaft puller (commercial service tool) (A) into joint
sub-assembly screw part to a length of 30 mm (1.18 in) or more.
Support drive shaft with one hand and pull out joint sub-assem-
bly from shaft.
CAUTION:
• Align a sliding hammer and drive shaft and remove them
by pulling firmly and uniformly.
• If joint sub-assembly cannot be pulled out, try after
removing drive shaft from vehicle. Refer to
"WHEEL SIDE : Disassembly and Assembly"
.
13. Remove circular clip from shaft.
14. Remove boot from shaft.
INSTALLATION
1.
Clean the old grease on joint sub-assembly with paper waste.
2.
Fill serration slot joint sub-assembly with NISSAN genuine grease or equivalent until the serration slot and
ball groove become full to the brim.
CAUTION:
After applying grease, use a paper waste to wipe off old grease that has oozed out.
13. Snap ring
14. Dust shield
15. Plate
16. Support bearing bracket
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
JPDIF0258ZZ
FRONT DRIVE SHAFT BOOT
FAX-13
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
3.
Install boot and boot bands to shaft.
CAUTION:
• Wrap serration on shaft with tape to protect the boot from damage.
• Never reuse boot and boot band.
4.
Remove the tape wrapped around the serration on shaft.
5.
Position the circular clip on groove at the shaft edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
6.
Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with joint sub-
assembly holding circular clip.
7.
Install joint sub-assembly (1) to shaft using plastic hammer.
CAUTION:
Confirm that joint sub-assembly is correctly engaged while
rotating drive shaft.
8.
Apply the specified amount of grease into the boot inside from
large diameter side of boot.
9.
Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on the shaft or joint sub-assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
10. To prevent the deformation of the boot, adjust the boot installa-
tion length (L) to the specified value shown below by inserting
the suitable tool into inside of the boot from the large diameter
side of the boot and discharging the inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with a tip of tool.
11. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool [SST: KV40107300 (
—
)]
(A).
CAUTION:
Never reuse boot band.
NOTE:
Grease amount
: Refer to
.
JPDIF0011ZZ
L
: Refer to
.
JPDIF0222ZZ
JPDIF0012ZZ
FAX-14
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT BOOT
Secure boot band so that dimension (A) meets the specification
as shown in the figure.
12. Secure joint sub-assembly and shaft, and then check that they
are in the correct position when rotating boot. Reinstall them
using boot bands when boot installation positions become incor-
rect.
CAUTION:
Never reuse boot band.
13. Clean the matching surface of wheel hub lock nut and wheel
hub and bearing assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
14. Insert drive shaft to wheel hub and bearing assembly, and then temporarily tighten wheel hub lock nut.
15. Install strut assembly to steering knuckle. Refer to
.
16. Install disc rotor. Refer to
BR-35, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
17. Install caliper assembly to steering knuckle. Refer to
BR-34, "BRAKE CALIPER ASSEMBLY : Exploded
.
18. Install lock plate to strut assembly. Refer to
BR-20, "FRONT : Exploded View"
.
19. Install wheel sensor and sensor harness to steering knuckle. Refer to
.
20. Tighten the wheel hub lock nut to the specified torque. Refer to
.
CAUTION:
Never use a power tool to tighten the wheel hub lock nut.
NOTE:
Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub and bearing assembly and axle housing.
21. Install cotter pin. Refer to
CAUTION:
• Never reuse cotter pin.
• Bend cotter pin at the root sufficiently to prevent any looseness.
22. Install tires. Refer to
.
TRANSAXLE SIDE
TRANSAXLE SIDE : Removal and Installation
INFOID:0000000009948796
NOTE:
Remove boot after removing drive shaft. Refer to
FAX-16, "LEFT SIDE : Removal and Installation"
(left side),
FAX-17, "RIGHT SIDE : Removal and Installation"
(right side).
Inspection
INFOID:0000000009948797
INSPECTION AFTER INSTALLATION
Check the following items, and replace the part it necessary.
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks, damage, and leakage of grease.
• Check wheel sensor harness for proper connection. Refer to
BRC-110, "FRONT WHEEL SENSOR :
.
• Adjust neutral position of steering angle sensor. Refer to
BRC-9, "Special Repair Requirement"
A
: 7.0 mm (0.276 in) or less
JPDIF0268ZZ
FRONT DRIVE SHAFT
FAX-15
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Exploded View
INFOID:0000000009948798
LEFT SIDE
RIGHT SIDE
1.
Circular clip
2.
Dust shield
3.
Housing
4.
Snap ring
5.
Spider assembly
6.
Boot band
7.
Boot
8.
Shaft
9.
Damper band
10. Dynamic damper
11.
Circular clip
12. Joint sub-assembly
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
JPDIF0266ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Shaft
6.
Damper band
7.
Dynamic damper
8.
Spider assembly
9.
Snap ring
10. Housing
11.
Dust shield
12. Support bearing
JPDIF0265GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст