Nissan Cube. Instruction — part 493
FAX-8
< PERIODIC MAINTENANCE >
FRONT DRIVE SHAFT
FRONT DRIVE SHAFT
Inspection
INFOID:0000000009948790
Check the following items, and replace the part if necessary.
• Check drive shaft mounting point and joint for looseness and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occurs from drive shaft.
• Check boot for cracks and other damage.
FRONT WHEEL HUB AND KNUCKLE
FAX-9
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
REMOVAL AND INSTALLATION
FRONT WHEEL HUB AND KNUCKLE
Exploded View
INFOID:0000000009948791
Removal and Installation
INFOID:0000000009948792
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-110, "FRONT WHEEL SENSOR : Exploded
.
3.
Remove lock plate from strut assembly. Refer to
BR-20, "FRONT : Exploded View"
.
4.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Exploded View"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
BR-35, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
6.
Remove cotter pin, and then loosen wheel hub lock nut with power tool.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing
assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.
8.
Remove wheel hub lock nut.
9.
Remove wheel hub and bearing assembly, and then remove splash guard.
10. Suspend the drive shaft with suitable wire.
11. Remove steering outer socket from steering knuckle. Refer to
.
12. Remove steering knuckle from transverse link.
1.
Steering knuckle
2.
Splash guard
3.
Wheel hub and bearing assembly
4.
Wheel hub lock nut
5.
Cotter pin
Refer to
JPDIF0263GB
FAX-10
< REMOVAL AND INSTALLATION >
FRONT WHEEL HUB AND KNUCKLE
13. Remove steering knuckle from strut assembly. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
• Tighten the wheel hub lock nut to the specified torque. Refer to
.
CAUTION:
Never use a power tool to tighten the wheel hub lock nut.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub and bearing assembly and axle housing.
• Never reuse cotter pin.
Inspection
INFOID:0000000009948793
INSPECTION AFTER REMOVAL
Check the following items, and replace the part it necessary.
• Check components for deformation, cracks, and other damage. Replace if necessary.
• Check boots of transverse link and steering outer socket ball joint for breakage, axial play, and torque. Refer
.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-110, "FRONT WHEEL SENSOR :
.
2.
Check the wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
FRONT DRIVE SHAFT BOOT
FAX-11
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT BOOT
Exploded View
INFOID:0000000009948794
LEFT SIDE
RIGHT SIDE
1.
Circular clip
2.
Dust shield
3.
Housing
4.
Snap ring
5.
Spider assembly
6.
Boot band
7.
Boot
8.
Shaft
9.
Damper band
10. Dynamic damper
11.
Circular clip
12. Joint sub-assembly
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
Refer to
for symbols not described on the above.
JPDIF0266ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Shaft
6.
Damper band
7.
Dynamic damper
8.
Spider assembly
9.
Snap ring
10. Housing
11.
Dust shield
12. Support bearing
JPDIF0265GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст