Nissan Cube. Instruction — part 993
TM-228
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
SECONDARY SPEED SENSOR
SECONDARY SPEED SENSOR
Exploded View
INFOID:0000000009949100
Removal and Installation
INFOID:0000000009949101
REMOVAL
1.
Remove air duct (inlet). Refer to
2.
Disconnect secondary speed sensor connector.
3.
Remove secondary speed sensor.
4.
Remove O-ring from secondary speed sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000009949102
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
1.
Secondary speed sensor
2.
O-ring
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JSDIA0751GB
DIFFERENTIAL SIDE OIL SEAL
TM-229
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000009949103
Removal and Installation
INFOID:0000000009949104
REMOVAL
1.
Remove front drive shaft assembly. Refer to
2.
Remove differential side oil seals using a flat-bladed screwdriver.
CAUTION:
Be careful not to scratch transaxle case and converter housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse differential side oil seals.
• Apply CVT fluid to differential side oil seals.
• When insert drive shaft, always use a protector [SST: KV38107900 ( — )]. Refer to
Install drive shaft using drifts [SST: ST35325000 ( — ) and
KV31103000 ( — )]. Check that side oil seal height difference from
case end surface is within the specified value “A” and “B”.
NOTE:
Differential side oil seal pulling direction is used as the reference.
Inspection
INFOID:0000000009949105
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
1.
RH differential side oil seal
2.
LH differential side oil seal
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
SCIA8345J
Dimension “A”
: Height difference from case end sur-
face is within 0
±
0.5 mm (0
±
0.020 in).
Dimension “B”
: Height difference from case end sur-
face is within 0
±
0.5 mm (0
±
0.020 in).
SCIA4076J
TM-230
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
CVT OIL WARMER SYSTEM
CVT OIL WARMER SYSTEM
WATER HOSE
WATER HOSE : Exploded View
INFOID:0000000009949106
WATER HOSE : Removal and Installation
INFOID:0000000009949107
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator.
CAUTION:
Perform this step engine is cold.
1.
Remove air duct (inlet). Refer to
2.
Remove hose clamps, and remove CVT water hose A.
3.
Remove hose clamps, and remove CVT water hose B.
4.
Remove hose clamps, and remove CVT water hose C.
5.
Remove CVT water tube.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Hose clamp
2.
CVT water hose C
3.
CVT water tube
4.
CVT water hose B
5.
Transaxle assembly
6.
CVT oil warmer
7.
CVT water hose A
A.
Water pump
B.
Water inlet-outlet
Refer to
for symbols in the figure.
JSDIA1290GB
CVT OIL WARMER SYSTEM
TM-231
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Insert CVT water hose according to dimension “A” described
below.
• Set hose clamps (1) at the both ends of fluid cooler hose (2) with
dimension “A” from the hose edge.
• Hose clamp should not interfere with the bulge.
*: Refer to the illustrations for the specific position of each hose clamp tab.
• The illustrations indicate the view from the hose ends.
• When installing hose clamps the center line of each clamp tab
should be positioned as shown in the figure.
WATER HOSE : Inspection
INFOID:0000000009949108
INSPECTION AFTER INSTALLATION
Start and warm up the engine. Visually check that there is no leakage of engine coolant and CVT fluid.
CVT FLUID COOLER HOSE
CVT FLUID COOLER HOSE : Exploded View
INFOID:0000000009949109
COMPONENT PARTS LOCATION
CVT water hose (1)
Insert side tube (2)
Dimension “A”
CVT water hose A
Water inlet-outlet
End reaches the spool portion (B)
CVT oil warmer
CVT water hose B
CVT oil warmer
CVT water tube
CVT water hose C
CVT water tube
Water pump
JSDIA1291ZZ
Dimension “A”
: 5 – 7 mm (0.20 – 0.28 in)
SCIA8123E
CVT water hose
Hose end
Paint mark
Position of hose clamp
*
CVT water hose A
Water inlet-outlet side
Facing forward
A
CVT oil warmer side
Facing forward
A
CVT water hose B
CVT oil warmer side
Facing to the right of the vehicle
B
CVT water tube side
Facing forward
A
CVT water hose C
CVT water tube side
Facing forward
A
Water pump side
Facing upward
C
D
: Vehicle front
E
: Vehicle upper
JSDIA1292ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст