Nissan Cube. Instruction — part 994
TM-232
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
CVT OIL WARMER SYSTEM
CVT FLUID COOLER HOSE : Removal and Installation
INFOID:0000000009949110
REMOVAL
1.
Remove air duct (inlet). Refer to
2.
Remove hose clamps, and remove CVT fluid cooler hose A.
3.
Remove hose clamps, and remove CVT fluid cooler hose B.
4.
Remove CVT fluid cooler tube A and CVT fluid cooler tube B.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing CVT fluid cooler tube (1) and (2) to transaxle
assembly, install them so that CVT fluid cooler tube rotation stop-
per (A) and (B) touch to transaxle case (C) and (D).
1.
CVT fluid cooler hose A
2.
Hose clamp
3.
CVT fluid cooler tube A
4.
Gasket
5.
Transaxle assembly
6.
CVT fluid cooler tube B
7.
CVT fluid cooler hose B
8.
CVT oil warmer
Refer to
for symbols in the figure.
JSDIA1288GB
: Vehicle front
JPDIA0698ZZ
CVT OIL WARMER SYSTEM
TM-233
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Insert CVT fluid cooler hose according to dimension “A” described
below.
• Set hose clamps (1) at the both ends of fluid cooler hose (2) with
dimension “A” from the hose edge.
• Hose clamp should not interfere with the bulge.
*: Refer to the illustrations for the specific position of each hose clamp tab.
• The illustrations indicate the view from the hose ends.
• When installing hose clamps the center line of each clamp tab
should be positioned as shown in the figure.
CVT FLUID COOLER HOSE : Inspection
INFOID:0000000009949111
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
CVT OIL WARMER
CVT fluid cooler hose (1)
Insert side tube (2)
Dimension “A”
CVT fluid cooler hose A
CVT fluid cooler tube
End reaches the 2-stage
bulge (B)
CVT oil warmer
CVT fluid cooler hose B
CVT oil warmer
CVT fluid cooler tube
JSDIA1289ZZ
Dimension “A”
: 5 – 7 mm (0.20 – 0.28 in)
SCIA8123E
CVT fluid cooler hose
Hose end
Paint mark
Position of hose clamp*
CVT fluid cooler hose A
CVT fluid cooler tube side
Vehicle front
A
CVT oil warmer side
Vehicle front
A
CVT fluid cooler hose B
CVT oil warmer side
Vehicle front
A
CVT fluid cooler tube side
Vehicle front
A
B
: Vehicle front
JPDIA0675ZZ
TM-234
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
CVT OIL WARMER SYSTEM
CVT OIL WARMER : Exploded View
INFOID:0000000009949112
CVT OIL WARMER : Removal and Installation
INFOID:0000000009949113
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator.
CAUTION:
Perform this step engine is cold.
1.
Remove CVT water hose from CVT oil warmer. Refer to
TM-230, "WATER HOSE : Exploded View"
2.
Remove CVT fluid cooler hose from CVT oil warmer. Refer to
TM-231, "CVT FLUID COOLER HOSE :
.
3.
Remove CVT oil warmer.
4.
Remove bracket.
INSTALLATION
Install in the reverse order of removal.
CVT OIL WARMER : Inspection
INFOID:0000000009949114
INSPECTION AFTER INSTALLATION
• Check for CVT fluid leakage and check CVT fluid level. Refer to
.
• Start and warm up the engine. Visually check that there is no leakage of engine coolant and CVT fluid.
1.
CVT oil warmer
2.
Bracket
3.
Transaxle assembly
Refer to
for symbols in the figure.
JPDIA0725GB
TRANSAXLE ASSEMBLY
TM-235
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000009949115
Removal and Installation
INFOID:0000000009949116
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator.
CAUTION:
• Perform this step engine is cold.
• When replacing TCM and transaxle assembly as a set, replace transaxle assembly first and then
replace TCM. Refer to
.
REMOVAL
1.
Remove battery. Refer to
.
2.
Remove air duct (inlet), air duct and air cleaner case. Refer to
.
3.
Remove air breather hose.
4.
Remove battery bracket.
5.
Disconnect following harness connector and wire harness.
• CVT unit connector. Refer to
TM-202, "Removal and Installation Procedure for CVT Unit Connector"
.
1.
CVT fluid level gauge
2.
CVT fluid charging pipe
3.
O-ring
4.
Transaxle assembly
A.
: Tightening must be done following the installation procedure. Refer to
TM-235, "Removal and Installation"
Refer to
JSDIA1185GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст