Nissan March K13. Instruction — part 614
SR-34
< REMOVAL AND INSTALLATION >
DEPLOYMENT AND DISPOSAL
The battery must show voltage of 9.6 V or more.
Remove the battery from the vehicle and place it on dry wood blocks
approximately 5.0 m (16.4 ft) away from the vehicle.
• Wait 3 minutes or more after the vehicle battery is disconnected
before proceeding.
• Connect red clip of deployment tool (A) to battery positive terminal
and black clip to negative terminal.
Check that the polarity is correct. The right side lamp in the
tool, marked “deployment tool power”, should illuminate with a
green light. If the right side lamp illuminates red, reverse the
connections to the battery.
Deployment Tool Check
Press the deployment tool switch (C) to the ON position. The left
side lamp in the tool, marked “air bag connector voltage” should illu-
minate (B). If it does not illuminate, replace the deployment tool (A).
Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)
*: If this lamp illuminates red, the tool is connected to the battery incorrectly. Reverse the connections and check that the lamp illumi-
nates green.
DEPLOYMENT OF FRONT PASSENGER AIR BAG MODULE (OUTSIDE OF VEHICLE)
1.
Remove the front passenger air bag module (2) from lid (1).
2.
Make 8.5 mm (0.335 in) diameter hole (B) in air bag module
bracket (SST: KV99105300) (A) at the position shown in figure.
JMHIA0204ZZ
JMHIA0205ZZ
Switch operation
Left side lamp, green*
“AIR BAG CONNECTOR VOLTAGE”
Right side lamp, green*
“DEPLOYMENT TOOL POWER”
OFF
OFF
ON
ON
ON
ON
JMHIA1539ZZ
JMHIA0225ZZ
DEPLOYMENT AND DISPOSAL
SR-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
3.
Firmly secure air bag module bracket (SST: KV99105300) (A) in
a vise.
4.
Insert two bolts (D) through air bag module bracket and front
passenger air bag module (1) lower side holes, and fix then with
two nuts.
5.
Connect deployment tool (SST: KV99106400) (B) and deploy-
ment tool adapter (SST: KV99110500) (C) to front passenger air
bag module.
6.
Connect red clip of deployment tool (A) to battery positive termi-
nal and black clip to negative terminal (B).
7.
The lamp on the right side of the tool, marked “deployment tool
power”, should illuminate green, not red.
8.
Press the button on the deployment tool (A). The left side lamp
on the tool, marked “air bag connector voltage”, illuminates and
the front passenger air bag module (1) deploys.
CAUTION:
• When deploying the front passenger air bag module,
never stand on the deploying side.
• Stand at least 5.0 m (16.4 ft) away from the front passen-
ger air bag module.
FRONT PASSENGER AIR BAG MODULE : Disposal
INFOID:0000000005891461
DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Deployed air bag module and seat belt pre-tensioner are very hot. Before disposing of air bag module and
seat belt pre-tensioner, wait at least 30 minutes or more, and 10 minutes or more, respectively. Seal them in a
plastic bag before disposal.
CAUTION:
• Never apply water to a deployed air bag module or seat belt
pre-tensioner.
• Always use gloves when handling a deployed air bag module
or seat belt pre-tensioner.
• No poisonous gas is produced upon air bag module deploy-
ment. However, be careful not to inhale gas since it irritates
the throat and can cause choking.
• Never disassemble the air bag module and seat belt pre-ten-
sioner.
• Air bag module and seat belt pre-tensioner cannot be reused.
• Wash your hands clean after the work is complete.
SIDE CURTAIN AIR BAG MODULE
SIDE CURTAIN AIR BAG MODULE : Deployment
INFOID:0000000006037637
CHECKING DEPLOYMENT TOOL
Connecting to Battery
CAUTION:
JMHIA1540ZZ
JMHIA0209ZZ
SBF276H
SR-36
< REMOVAL AND INSTALLATION >
DEPLOYMENT AND DISPOSAL
The battery must show voltage of 9.6 V or more.
Remove the battery from the vehicle and place it on dry wood blocks
approximately 5.0 m (16.4 ft) away from the vehicle.
• Wait 3 minutes or more after the vehicle battery is disconnected
before proceeding.
• Connect red clip of deployment tool (A) to battery positive terminal
and black clip to negative terminal.
Check that the polarity is correct. The right side lamp in the
tool, marked “deployment tool power”, should illuminate with a
green light. If the right side lamp illuminates red, reverse the
connections to the battery.
Deployment Tool Check
Press the deployment tool switch (C) to the ON position. The left
side lamp in the tool, marked “air bag connector voltage” should illu-
minate (B). If it does not illuminate, replace the deployment tool (A).
Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)
*: If this lamp glows red, the tool is connected to the battery incorrectly. Reverse the connections and check the lamp glows green.
DEPLOYMENT OF SIDECURTAIN AIR BAG MODULE (OUTSIDE OF VEHICLE)
1.
Cut the inflator (1) from side curtain air bag module (2).
2.
Connect deployment tool adapter (SST: KV99110500) (B) and
deployment tool (SST: KV99106400) (A) to the inflator (1).
JMHIA0204ZZ
JMHIA0205ZZ
Switch operation
Left side lamp, green*
“AIR BAG CONNECTOR VOLTAGE”
Right side lamp, green*
“DEPLOYMENT TOOL POWER”
OFF
OFF
ON
ON
ON
ON
JMHIA1541ZZ
JMHIA1542ZZ
DEPLOYMENT AND DISPOSAL
SR-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
3.
Put the inflator connected with the deployment tool (SST:
KV99106400) and deployment tool adapter (SST: KV99110500)
into a tire without a wheel.
4.
Put the tire with the inflator (1) onto another tire without a wheel.
Add an additional tire without a wheel and then a tire mounted
on a wheel on top.
CAUTION:
Tie all tires together with a strap in order keep them stand-
ing.
5.
Connect red clip of deployment tool (A) to battery positive termi-
nal and black clip to negative terminal.
6.
The lamp on the right side of the tool, marked “deployment tool
power”, should illuminate green, not red.
7.
Press the button on the deployment tool (A). The left side lamp
on the tool, marked “air bag connector voltage”, will illuminate
and the air bag module inflator (1) will deploy.
CAUTION:
When deploying the side curtain air bag module, stand at least 5.0 m (16.4 ft) away from the side
curtain air bag module.
SIDE CURTAIN AIR BAG MODULE : Disposal
INFOID:0000000006037638
DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Deployed air bag module and seat belt pre-tensioner are very hot. Before disposing of air bag module and
seat belt pre-tensioner, wait at least 30 minutes or more, and 10 minutes or more, respectively. Seal them in a
plastic bag before disposal.
CAUTION:
• Never apply water to a deployed air bag module or seat belt
pre-tensioner.
• Always use gloves when handling a deployed air bag module
or seat belt pre-tensioner.
• No poisonous gas is produced upon air bag module deploy-
ment. However, be careful not to inhale gas since it irritates
the throat and can cause choking.
• Never disassemble the air bag module and seat belt pre-ten-
sioner.
• Air bag module and seat belt pre-tensioner cannot be reused.
• Wash your hands clean after the work is complete.
SEAT BELT PRE-TENSIONER
SEAT BELT PRE-TENSIONER : Deployment
INFOID:0000000005891464
CHECKING DEPLOYMENT TOOL
Connecting to Battery
CAUTION:
PHIA0937J
PHIA1173E
SBF276H
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст