Nissan March K13. Instruction — part 613
SR-30
< REMOVAL AND INSTALLATION >
DIAGNOSIS SENSOR UNIT
CAUTION:
• Never impact the diagnosis sensor unit.
• Replace the diagnosis sensor unit if it has been dropped or
sustained an impact.
• Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-ten-
sioner.
INSTALLATION
Install air bag diagnosis sensor unit in the reverse order of removal.
CAUTION:
• Never use the old bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT-III that the ECU discrimi-
nated number (identification number) of the new replacement air bag diagnosis sensor unit matches
the ECU discriminated number (identification number) of the replaced (old) air bag diagnosis sensor
unit.
NOTE:
If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU
discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify
that the correct air bag diagnosis sensor unit was installed.
JMHIA0009ZZ
SEAT BELT PRE-TENSIONER
SR-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SEAT BELT PRE-TENSIONER
Exploded View
INFOID:0000000005891456
Removal and Installation
INFOID:0000000005891457
For removal and installation procedures, refer to
SB-6, "SEAT BELT RETRACTOR : Removal and Installa-
.
SR-32
< REMOVAL AND INSTALLATION >
DEPLOYMENT AND DISPOSAL
DEPLOYMENT AND DISPOSAL
DRIVER AIR BAG MODULE
DRIVER AIR BAG MODULE : Deployment
INFOID:0000000005891458
CHECKING DEPLOYMENT TOOL
Connecting to Battery
CAUTION:
The battery must show voltage of 9.6 V or more.
Remove the battery from the vehicle and place it on dry wood blocks
approximately 5.0 m (16.4 ft) away from the vehicle.
• Wait 3 minutes or more after the vehicle battery is disconnected
before proceeding.
• Connect red clip of deployment tool (A) to battery positive terminal
and black clip to negative terminal.
Check that the polarity is correct. The right side lamp in the
tool, marked “deployment tool power”, should illuminate with a
green light. If the right side lamp illuminates red, reverse the
connections to the battery.
Deployment Tool Check
Press the deployment tool switch (C) to the ON position. The left
side lamp in the tool, marked “air bag connector voltage” should illu-
minate (B). If it does not illuminate, replace the deployment tool (A).
Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)
*: If this lamp illuminates red, the tool is connected to the battery incorrectly. Reverse the connections and check that the lamp illumi-
nates green.
DEPLOYMENT OF DRIVER AIR BAG MODULE (OUTSIDE OF VEHICLE)
1.
Unless the vehicle is being scrapped, deploying the air bag in
the vehicle is not recommended. This may cause damage to the
vehicle interior.
Anchor air bag module bracket (SST: KV99105300) (A) in a vice
secured to a firm foundation deployment.
JMHIA0204ZZ
JMHIA0205ZZ
Switch operation
Left side lamp, green*
“AIR BAG CONNECTOR VOLTAGE”
Right side lamp, green*
“DEPLOYMENT TOOL POWER”
OFF
OFF
ON
ON
ON
ON
JMHIA0208ZZ
DEPLOYMENT AND DISPOSAL
SR-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2.
Using wire (D), secure driver air bag module (1) to air bag mod-
ule bracket (SST: KV99105300) (A) at two places.
CAUTION:
Use wire of at least 1.0 mm (0.039 in) diameter.
3.
Firmly secure air bag module bracket (SST: KV99105300) with
driver air bag module attached, in a vise.
4.
Connect deployment tool adapter (SST: KV99110500) (C) to
driver air bag module and deployment tool connector (SST:
KV99106400) (B).
5.
Connect red clip of deployment tool (A) to battery positive termi-
nal and black clip to negative terminal (B).
6.
The lamp on the right side of the tool, marked “deployment tool
power”, should illuminate green, not red.
7.
Press the button on the deployment tool. The left side lamp on
the tool, marked “air bag connector voltage”, illuminates and the
air bag module (1) deploys.
CAUTION:
When deploying the driver air bag module, stand at least 5.0
m (16.4 ft) away from the air bag module.
DRIVER AIR BAG MODULE : Disposal
INFOID:0000000005891459
DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Deployed air bag module and seat belt pre-tensioner are very hot. Before disposing of air bag module and
seat belt pre-tensioner, wait at least 30 minutes or more, and 10 minutes or more, respectively. Seal them in a
plastic bag before disposal.
CAUTION:
• Never apply water to a deployed air bag module or seat belt
pre-tensioner.
• Always use gloves when handling a deployed air bag module
or seat belt pre-tensioner.
• No poisonous gas is produced upon air bag module deploy-
ment. However, be careful not to inhale gas since it irritates
the throat and can cause choking.
• Never disassemble the air bag module and seat belt pre-ten-
sioner.
• Air bag module and seat belt pre-tensioner cannot be reused.
• Wash your hands clean after the work is complete.
FRONT PASSENGER AIR BAG MODULE
FRONT PASSENGER AIR BAG MODULE : Deployment
INFOID:0000000005891460
CHECKING DEPLOYMENT TOOL
Connecting to Battery
CAUTION:
JMHIA1043ZZ
JMHIA0209ZZ
SBF276H
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст