Nissan March K13. Instruction — part 419
REAR DOOR FINISHER
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3.
Insert a remover tool (A) between power window switch finisher
(1) and rear door finisher (2) to disengage fixing pawls.
CAUTION:
Apply protective tape (B) to the rear door finisher to protect
from damage.
4.
Remove power window switch finisher, and then disconnect power window switch harness connector.
5.
Remove rear door finisher fixing screw.
6.
Insert a remover tool (A) between rear door panel (1) and rear
door finisher (2) to disengage fixing clips and metal clips.
CAUTION:
Insert remover tool into part shown in the figure.
(Between clips and door panel).
7.
Remove rear door finisher from rear door panel.
Instruction window models
1.
Fully open door window.
2.
Remove regulator handle.
NOTE:
Insert hook and pick tool (A) between regulator handle (1) and
regulator sealer to remove sanp pin (2).
3.
Remove door pull handle fixing TORX screw with a screwdriver.
: Pawl
JMJIA4088ZZ
: Clip
: Metal clip
JMJIA4089ZZ
JMJIA0491ZZ
JMJIA4096ZZ
INT-20
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
4.
Insert a remover tool (A) between door pull handle (1) and rear
door finisher (2) to disengage fixing pawls and then remove door
pull handle.
CAUTION:
Apply protective tape (B) to the rear door finisher to protect
from damage.
5.
Remove rear door finisher fixing screw.
6.
Insert a remover tool (A) between rear door panel (1) and rear
door finisher (2) to disengage fixing clips and metal clips.
CAUTION:
Insert remover tool into part shown in the figure.
(Between clips and door panel).
7.
Remove rear door finisher from rear door panel.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing door finisher, check that all clips and metal clips are securely fitted in holes on body,
and then press them in.
: Pawl
JMJIA4092ZZ
: Clip
: Metal clip
JMJIA4093ZZ
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000006046524
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000006046553
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
REMOVAL
1.
Remove front kicking plate. Refer to
INT-22, "KICKING PLATE INNER : Removal and Installation"
.
1.
Front pillar garnish
2.
Front body side welt
3.
Dash side finisher
4.
Front kicking plate inner
5.
Center pillar lower garnish
6.
Rear kicking plate inner
7.
Rear body side welt
8.
Center pillar upper garnish
: Clip
: Pawl
: Metal clip
JMJIA4094ZZ
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2.
Disengage dash side finisher fixing metal clips, and then remove
dash side finisher.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check that all clips are securely fitted in panel holes on body, and then press them in.
FRONT PILLAR GARNISH
FRONT PILLAR GARNISH : Removal and Installation
INFOID:0000000006046552
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
REMOVAL
1.
Release front pillar portion of front body side welt.
2.
Disengage front pillar garnish fixing metal clips with remover tool
(A), and then remove front pillar garnish.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check that all metal clips are securely fitted in panel holes on body, and then press
them in.
KICKING PLATE INNER
KICKING PLATE INNER : Removal and Installation
INFOID:0000000006046554
CAUTION:
Never damage the body.
REMOVAL
FRONT KICKNG PLATE INNER
: Metal clip
JMJIA4081ZZ
: Metal clip
JMJIA4079ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст