Nissan March K13. Instruction — part 420
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
1.
Pull up front kicking plate inner to disengage fixing pawls.
2.
Remove front kicking plate inner from body panel.
REAR KICKING PLATE INNER
1.
Pull up rear kicking plate inner to disengage fixing clip, pawls
and metal clip.
2.
Remove rear kicking plate inner from body panel.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check that all clip, pawls and metal clip are securely fitted in panel holes on body, and
then press them in.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000006046555
CAUTION:
Never damage the body.
REMOVAL
FRONT BODY SIDE WELT
1.
Remove front kicking plate inner. Refer to
INT-22, "KICKING PLATE INNER : Removal and Installation"
2.
Remove dash side finisher. Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installation"
.
3.
Remove center pillar lower garnish. Refer to
INT-23, "CENTER PILLAR LOWER GARNISH : Removal
4.
Remove front body side welt.
REAR BODY SIDE WELT
1.
Remove rear kicking plate inner. Refer to
INT-22, "KICKING PLATE INNER : Removal and Installation"
.
2.
Remove center pillar lower garnish. Refer to
INT-23, "CENTER PILLAR LOWER GARNISH : Removal
3.
Remove rear body side welt.
INSTALLATION
Install in the reverse order of removal.
CENTER PILLAR LOWER GARNISH
CENTER PILLAR LOWER GARNISH : Removal and Installation
INFOID:0000000006046556
CAUTION:
: Pawl
JMJIA4080ZZ
: Clip
: Pawl
: Metal clip
JMJIA4082ZZ
INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
Never damage the body.
REMOVAL
1.
Slide front seat assembly to the front most.
2.
Remove front kicking plate inner and rear kicking plate inner. Refer to
INT-22, "KICKING PLATE INNER :
.
3.
Spread center pillar lower garnish where it is engaged to body
side panel, disengage vehicle front side disengage vehicle rear
side.
4.
Remove center pillar lower garnish from body panel.
INSTALLATION
Install in the reverse order of removal.
CENTER PILLAR UPPER GARNISH
CENTER PILLAR UPPER GARNISH : Removal and Installation
INFOID:0000000006046557
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
REMOVAL
CENTER PILLAR UPPER GARNISH
1.
Remove front seat belt outer anchor bolt. Refer to
SB-6, "SEAT BELT RETRACTOR : Exploded View"
2.
Remove center pillar lower garnish. Refer to
INT-23, "CENTER PILLAR LOWER GARNISH : Removal
3.
Remove front body side welt and rear body side welt. Refer to
INT-23, "BODY SIDE WELT : Removal and
.
4.
Disengage center pillar upper garnish lower side fixing pawl with
a remover tool (A).
5.
Pull center pillar upper garnish (1) from inside passenger room, disengage center pillar upper garnish
upper side fixing pawl as shown in the figure below, and then remove center pillar upper garnish from cen-
ter pillar panel (2).
JMJIA4133ZZ
: Pawl
JMJIA4130ZZ
BODY SIDE TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing, check that pawls and are securely fitted in panel holes on body, and then press them
in.
JMJIA1176ZZ
INT-26
< REMOVAL AND INSTALLATION >
FLOOR TRIM
FLOOR TRIM
Exploded View
INFOID:0000000006046526
Removal and Installation
INFOID:0000000006046527
REMOVAL
1.
Remove front seat assembly (LH/RH). Refer to
SE-15, "Removal and Installation"
.
2.
Remove rear seat cushion and seatback assembly. Refer to
SE-19, "Removal and Installation"
3.
Remove instrument panel assembly and center console assembly. Refer to
4.
Remove A/C unit assembly. Refer to
HA-42, "A/C UNIT ASSEMBLY : Removal and Installation"
.
5.
Disconnect harness connector from diagnosis sensor unit. Refer to
6.
Remove shift control assembly. Refer to
TM-15, "Removal and Installation"
.
7.
Remove parking brake lever assembly. Refer to
PB-3, "Removal and Installation"
.
8.
Remove front kicking plate inner and rear kicking plate inner (LH/RH). Refer to
INNER : Removal and Installation"
9.
Remove dash side finisher (LH/RH). Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installation"
.
10. Remove front seat belt outer anchor bolt. Refer to
.
1.
Floor carpet assembly
2.
Floor hook
3.
Front floor spacer RH
4.
Front floor spacer LH
5.
Rear floor spacer LH
6.
Luggage floor spacer front
7.
Luggage floor spacer rear
8.
Tool box
9.
Tool box cover
10.
Rear floor spacer RH
: Vehicle front
JMJIA4097ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст