Nissan March K13. Instruction — part 421
FLOOR TRIM
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
11. Remove center pillar lower garnish (LH/RH). Refer to
INT-23, "CENTER PILLAR LOWER GARNISH :
.
12. Disengage clip of floor hook (1) with remover tool (A).
13. Disengage floor trim fixing clip (A) and then remove floor trim.
INSTALLATION
Install in the reverse order of removal.
: Clip
JMJIA0092GB
: Vehicle front
JMJIA4083ZZ
INT-28
< REMOVAL AND INSTALLATION >
HEADLINING
HEADLINING
Exploded View
INFOID:0000000006054248
Removal and Installation
INFOID:0000000006054249
REMOVAL
1.
Remove front kicking plate inner (LH/RH) and rear kicking plate inner (LH/RH). Refer to
PLATE INNER : Removal and Installation"
.
2.
Remove center pillar lower garnish (LH/RH). Refer to
INT-23, "CENTER PILLAR LOWER GARNISH :
.
3.
Remove front body side welt (LH/RH) and rear body side welt (LH/RH). Refer to
WELT : Removal and Installation"
4.
Remove luggage side upper finisher (LH/RH). Refer to
INT-31, "LUGGAGE SIDE UPPER FINISHER :
.
1.
Assist grip cap
2.
Rear assist grip (RH)
3.
Headlining assembly
4.
Inside mirror cover
Sunvisor assembly (RH)
5.
Sunvisor holder (LH/RH)
6.
Sunvisor assembly (LH)
7.
Front assist grip (LH)
8.
Rear assist grip (LH)
JMJIA4095ZZ
HEADLINING
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
5.
Remove center pillar upper garnish (LH/RH). Refer to
INT-24, "CENTER PILLAR UPPER GARNISH :
.
6.
Remove front pillar garnish (LH/RH). Refer to
INT-22, "FRONT PILLAR GARNISH : Removal and Installa-
7.
Remove all assist grip.
• Lift assist grip cap while sliding and disengage assist grip cap
and assist grip.
• Remove mounting bolts.
• Pull out the assist grip to remove.
8.
Remove sunvisor assembly fixing screws, and then remove sunvisor assembly (LH/RH).
9.
Rotate the sunvisor holder (LH/RH) at approximately 90 degrees and then pull it down to remove.
10. Remove map lamp assembly. Refer to
INL-35, "Removal and Installation"
11. Remove headlining clips located at the rear side with a remover tool.
12. Remove headlining assembly through the back door.
CAUTION:
• When removing headlining, 2 workers are required.
• Be careful not to scratch or damage any part of the body
while taking out the headlining.
• Never bend headlining when removing.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• Never bend headlining when installing.
• When installing, start by installing both sunvisor holders and headlining clips in order to keep the
headlining in position.
JMJIA4130ZZ
JMJIA4131ZZ
JMJIA4084ZZ
INT-30
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
LUGGAGE FLOOR TRIM
Exploded View
INFOID:0000000006046532
LUGGAGE REAR PLATE
LUGGAGE REAR PLATE : Removal and Installation
INFOID:0000000006046533
REMOVAL
1.
Luggage side upper finisher LH
2.
Luggage side lower finisher clip (LH/
RH)
3.
Luggage side lower finisher LH
4.
Luggage side lower finisher lid (LH/
RH)
5.
Luggage rear plate
6.
Rope hook
7.
Luggage room lamp
8.
Luggage side lower finisher RH
9.
Luggage side upper finisher RH
10. Tonneau cover
: Clip
: Pawl
: Metal clip
: Vehicle front
JMJIA4098ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст