Nissan Versa Sedan. Instruction — part 249
DLK-314
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000009269023
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000009269024
REMOVAL
1. Fully open fuel filler lid.
2. Remove fuel cap pin (1).
3. Remove fuel filler lid screws and fuel filler lid.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
1.
Fuel filler lid opener cable
2.
Spring
3.
Fuel filler lid assembly
4.
Bumper rubber
5.
Fuel filler lid lock assembly
6.
Cable protector
Clip
JMKIA8174ZZ
JMKIA8137ZZ
FUEL FILLER LID OPENER
DLK-315
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000009269025
REMOVAL
1. Remove hood and fuel filler handle assembly bolts (A).
2. Disconnect fuel filler lid opener cable (2) by pulling downward
and then sliding cable end to the side to remove from hood and
fuel filler handle assembly (1).
3. Remove dash side finisher (LH). Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installation"
4. Remove center pillar lower finisher (LH). Refer to
INT-23, "CENTER PILLAR LOWER FINISHER :
.
5. Remove trunk side finisher (LH). Refer to
INT-33, "TRUNK SIDE FINISHER : Removal and Installation"
.
6. Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to
LOCK : Removal and Installation"
.
7. Disengage each harness protector (1), and then remove fuel
filler lid opener cable (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
NOTE:
• The following table shows the specifications for a correctly installed fuel filler lid.
• Fitting adjustment cannot be performed.
JMKIA7998ZZ
JMKIA7999ZZ
JMKIA5720ZZ
DLK-316
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FUEL FILLER LID OPENER
Unit: mm (in)
FUEL FILLER LID LOCK
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000009269026
REMOVAL
1. Fully open fuel filler lid.
2. Remove trunk side finisher (LH). Refer to
INT-33, "TRUNK SIDE FINISHER : Removal and Installation"
.
3. Release pawls (A) and remove fuel filler lid lock assembly (1)
from opening.
CAUTION:
Be careful not to damage gasket (2) when removing.
4. Disconnect fuel filler lid opener cable (1) by pulling downward
and then sliding cable end to the side to remove from fuel filler
lid lock assembly (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
Portion
Measurement
Standard
Fuel filler lid – Body side outer
Clearance
3.0
± 1.0 (0.12 ± 0.04)
Fuel filler lid – Body side outer
Surface height
0.0
± 1.0 (0.0 ± 0.04)
JMKIA8138ZZ
JMKIA8139ZZ
DOOR SWITCH
DLK-317
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR SWITCH
Exploded View
INFOID:0000000009269027
Removal and Installation
INFOID:0000000009269028
REMOVAL
1. Remove the door switch bolt (A).
2. Disconnect the harness connector from door switch (1) and
remove.
INSTALLATION
Installation is in the reverse order of removal.
1.
Door switch
2.
Door switch bolt
AWKIA1893ZZ
JMKIA2173ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст