Nissan Versa Sedan. Instruction — part 214
DLK-174
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
6. Disengage inside handle cable (3) and lock knob cable (2), and
then remove inside handle (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009268874
REMOVAL
1. Fully close rear door glass.
2. Remove rear door finisher. Refer to
INT-17, "Removal and Installation"
.
3. Remove sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape remain on the sealing screen, if the sealing screen
is reused.
4. Remove door side grommet, and loosen bolt from grommet
hole.
5. While pulling outside handle, remove outside handle escutch-
eon.
JMKIA5885ZZ
JMKIA1467ZZ
JMKIA5342ZZ
REAR DOOR LOCK
DLK-175
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
6. Pull outside handle (1) rearward and outward to remove.
7. Remove front gasket (1) and rear gasket (2).
: Front
8. Slide outside handle bracket toward rear of vehicle to remove.
: Front
9. Disconnect outside handle cable (1) from outside handle bracket
(2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check door open/close, lock/unlock operation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA0524ZZ
JMKIA5889ZZ
JMKIA5890ZZ
JMKIA5891ZZ
DLK-176
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID LOCK
TRUNK LID LOCK
Exploded View
INFOID:0000000009268875
TRUNK LID LOCK
TRUNK LID LOCK : Removal and Installation
INFOID:0000000009268876
REMOVAL
1. Remove trunk lid finisher (if equipped). Refer to
INT-35, "Removal and Installation"
.
2. Release rod holder (1) by lifting upward, and then separate trunk
lid lock rod (3) from trunk lid lock assembly (2).
3. Remove trunk lid lock assembly bolts.
1.
Trunk lid opener handle
2.
Trunk lid opener cable
3.
Cable protector
4.
Trunk lid striker
5.
Trunk lid lock assembly
6.
Key rod
7.
Trunk key cylinder
JMKIA8173GB
JMKIA8131ZZ
TRUNK LID LOCK
DLK-177
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4. Disconnect harness connector and then remove trunk lid lock
assembly (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check trunk lid open/close, lock/unlock operation.
• Check trunk lid lock assembly for poor lubrication. Apply a
suitable multi-purpose grease to trunk lid lock if necessary.
TRUNK LID OPENER HANDLE
TRUNK LID OPENER HANDLE : Removal and Installation
INFOID:0000000009268877
REMOVAL
1. Remove front kicking plate (LH). Refer to
INT-20, "KICKING PLATE INNER : Removal and Installation"
.
2. Disengage pawl using a suitable tool (A) and open the harness
clip.
: Pawl
3. Position floor carpet aside as necessary to access the trunk lid opener handle bolts.
4. Remove the trunk lid opener handle bolts.
5. Remove trunk lid opener cable from trunk lid opener handle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check rear door open/close, lock/unlock operation.
• After installation, perform the rear door adjustment procedure. Refer to
.
TRUNK LID OPENER CABLE
JMKIA8132ZZ
JMKIA8133ZZ
AWJIA0737ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст