Nissan Versa Sedan. Instruction — part 435
EXT-26
< REMOVAL AND INSTALLATION >
FENDER PROTECTOR
FENDER PROTECTOR
Exploded View
INFOID:0000000009268560
Removal and Installation
INFOID:0000000009268561
REMOVAL
1. Remove under cover. Refer to
EXT-19, "Removal and Installation"
2. Remove fender protector screws and clips.
3. Remove fender protector.
INSTALLATION
Installation is in the reverse order of removal.
1.
Fender protector
2.
J-nut
Front
JMKIA8068ZZ
ROOF SIDE MOLDING
EXT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF SIDE MOLDING
Exploded View
INFOID:0000000009268562
Removal and Installation
INFOID:0000000009268563
REMOVAL
1. Release roof side molding clip using a suitable tool (A).
: Clip
CAUTION:
Apply protective tape (B) on body to protect the painted
surface from damage.
2. Remove roof side molding, starting from the front of vehicle and moving toward the rear.
CAUTION:
Do not pull the roof side molding with too much force.
INSTALLATION
Installation is in the reverse order of removal.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
Removal
1.
Roof side molding
2.
Roof side molding clip
3.
Roof panel
4.
Body side outer panel
JMKIA8048ZZ
JMKIA5401ZZ
EXT-28
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
1. Remove roof side molding.
2. Heat adhesive tape interface using a dryer and then peel roof side molding clips (body side) using a suit-
able tool.
CAUTION:
Be careful not to damage the body.
Installation
1. Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2. Use two-part epoxy adhesive.
3. Apply adhesive evenly to clip tape surface.
4. Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5. Tape clips after press fit, and temporarily hold it for specified time based on the following.
6. Install roof side molding from rear of vehicle to front, in this order after temporarily holding.
CAUTION:
• Use double-sided tape after hardening for clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield portion, check that molding fastener is securely
inserted and then press in.
• Do not wash the vehicle within 24 hours so as to keep adhesive dry.
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit : 19.6 N (2.0 Kg - 4.41 lb)
× 2 seconds
5 to 10
°C (41 to 50 °F)
: 1 hour or more
11 to 23
°C (52 to 73 °F)
: 30 minutes or more
24
°C or more (75 °F or more) : 15 minutes or more
DOOR OUTSIDE MOLDING
EXT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
DOOR OUTSIDE MOLDING
Exploded View
INFOID:0000000009268564
Removal and Installation
INFOID:0000000009268565
FRONT DOOR OUTSIDE MOLDING
Removal
1. Open front door glass.
2. Release pawl, twist front door outside molding toward the outside of the vehicle and lift up and remove.
Installation
Installation is in the reverse order of removal.
REAR DOOR OUTSIDE MOLDING
Removal
1. Open door glass.
2. Release pawl, twist door outside molding toward the outside of the vehicle and lift up and remove.
Installation
Installation is in the reverse order of removal.
1.
Front door panel
2.
Rear door panel
3.
Front door outside molding
4.
Rear door outside molding
Pawl
JMKIA8045GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст