Nissan Versa Sedan. Instruction — part 828
TM-218
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
OVERDRIVE CONTROL SWITCH
OVERDRIVE CONTROL SWITCH
Component Function Check
INFOID:0000000009268004
1.
CHECK O/D INDICATOR LAMP FUNCTION
Check O/D OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?
YES
>> GO TO 2.
NO
>> Go to
2.
CHECK O/D SWITCH FUNCTION
1. Shift the selector lever to “D” position.
2. Check that O/D OFF indicator lamp turns ON/OFF when sport mode switch is operated.
Is the inspection results normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009268005
1.
CHECK OVERDRIVE CONTROL SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect A/T shift selector connector.
3. Turn ignition switch ON.
4. Check the voltage between A/T shift selector harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK OVERDRIVE CONTROL SWITCH
Check overdrive control switch. Refer to
TM-219, "Component Inspection (Overdrive Control Switch)"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK GROUND CIRCUIT
Check the continuity between A/T shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK CIRCUIT BETWEEN COMBINATION METER AND A/T SHIFT SELECTOR (PART 1)
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check the continuity between combination meter harness connector terminal and A/T shift selector har-
ness connector terminal.
A/T shift selector harness connector
Voltage
Connector
Terminal
M38
1
2
Approx. 5 V
A/T shift selector harness connector
Ground
Continuity
Connector
Terminal
M38
2
Ground
Existed
OVERDRIVE CONTROL SWITCH
TM-219
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK CIRCUIT BETWEEN COMBINATION METER AND A/T SHIFT SELECTOR (PART 2)
Check the continuity between combination meter harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK COMBINATION METER INPUT SIGNAL
1. Connect all of the disconnected connectors.
2. Turn ignition switch ON.
3. Select “Data Monitor” in “METER/M&A”.
4. Select “O/D OFF SW”.
5. Check that “O/D OFF SW” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace combination meter. Refer to
MWI-53, "Removal and Installation"
Component Inspection (Overdrive Control Switch)
INFOID:0000000009268006
1.
CHECK OVERDRIVE CONTROL SWITCH
Check the continuity between wires of selector lever knob (1)
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the selector lever knob. Refer to
.
Combination meter harness connector
A/T shift selector harness connector
Continuity
Connector
Terminal
Connector
Terminal
M24
28
M38
1
Existed
Combination meter harness connector
Ground
Continuity
Connector
Terminal
M24
28
Ground
Not existed
Condition
Continuity
Overdrive control switch is depressed
Existed
Overdrive control switch is released
Not existed
JSDIA1969ZZ
TM-220
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
OD OFF INDICATOR LAMP
OD OFF INDICATOR LAMP
Component Function Check
INFOID:0000000009268007
1.
CHECK O/D OFF INDICATOR LAMP FUNCTION
Check O/D OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009268008
1.
CHECK DTC (TCM)
With CONSULT
1. Turn ignition switch ON.
2. Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 2.
2.
CHECK DTC (COMBINATION METER)
With CONSULT
Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT SIGNAL
With CONSULT
1. Shift the selector lever to “D” position.
2. Select “Data Monitor” in “METER/M&A”.
3. Select “O/D OFF IND”.
4. Check that “O/D OFF IND” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-53, "Removal and Installation"
NO
>> GO TO 4.
4.
CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1. Select “Data Monitor” in “TRANSMISSION”.
2. Select “OD CONT SW”.
3. Check that “OD CONT SW” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-53, "Removal and Installation"
NO
>> Check overdrive control switch. Refer to
SHIFT POSITION INDICATOR CIRCUIT
TM-221
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHIFT POSITION INDICATOR CIRCUIT
Component Parts Function Inspection
INFOID:0000000009268009
1.
CHECK SHIFT POSITION INDICATOR
1. Start the engine.
2. Shift the selector lever.
3. Check that the selector lever position and the shift position indicator on the combination meter are identi-
cal.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009268010
1.
CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “RANGE”.
4. Shift the selector lever.
5. Check that selector lever position, “RANGE” on the CONSULT screen, and shift position indicator display
on the combination meter are identical.
Is the check result normal?
YES
>> INSPECTION END
NO-1 (“RANGE” is changed but is not displayed on the shift position indicator.>>Check
“Self
Diagnostic
Result” in “TRANSMISSION”.
NO-2 (“RANGE” and shift position indicator are different.)>>Check “Self Diagnostic Result” in “TRANSMIS-
SION”.
NO-3 (Specific“RANGE” is not displayed on the shift position indicator.)>>Check “Self Diagnostic Result” in
“METER/M&A”.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст