Nissan Altima L32. Instruction — part 1420
TM-24
< ON-VEHICLE REPAIR >
[6MT: RS6F52A]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000004201591
QR25DE engine models
VQ35DE engine models
Removal and Installation
INFOID:0000000004201592
Refer to the figure for air breather hose removal and installation information.
CAUTION:
• Install air breather hose with paint mark and clip facing front.
• Install air breather hose onto air breather tube until overlap area reaches the spool.
• Install air breather hose to air cleaner case by fully inserting the clip.
ALDIA0041ZZ
1.
Clip
2.
Air cleaner case
3.
Transaxle assembly
4.
Clip
5.
Air breather hose
A.
Set paint mark and clip at front side
⇐: Front
ALDIA0042ZZ
1.
Air cleaner case
2.
Transaxle assembly
3.
Clip
4.
Air breather hose
5.
Clip
A.
Set paint mark and clip at front side
⇐: Front
AIR BREATHER HOSE
TM-25
< ON-VEHICLE REPAIR >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Make sure there are no pinched or restricted areas on air breather hose caused by bending or wind-
ing when installing it.
TM-26
< REMOVAL AND INSTALLATION >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000004201593
Removal and Installation
INFOID:0000000004201594
CAUTON:
If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder).
Inserted CSC returns to the original position when removing transaxle assembly. Dust on clutch disc
sliding parts may damage CSC seal and may cause clutch fluid leakage.
REMOVAL
1. Remove the engine and transaxle as an assembly. Refer to
EM-72, "Removal and Installation"
(QR25DE),
EM-202, "Removal and Installation"
CAUTION:
Do not depress clutch pedal during removal procedure.
2. Disconnect the electrical connectors from the following:
• Back-up lamp switch
• Park/neutral position switch
3. Remove the harness from the transaxle.
4. Remove the starter motor. Refer to
STR-25, "Removal and Installation"
5. Remove the transaxle to engine and engine to transaxle bolts.
1.
Transaxle assembly
2.
LH engine mounting bracket
A.
ALDIA0049GB
TRANSAXLE ASSEMBLY
TM-27
< REMOVAL AND INSTALLATION >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6. Separate the transaxle from the engine.
7. If necessary remove the following:
• Air breather hose
• Switches
• LH engine mount
• Brackets
INSTALLATION
Installation is in the reverse order of removal.
• If transaxle is removed from the vehicle, always replace CSC. Refer to
CL-13, "Removal and Installation"
.
• When installing the transaxle assembly to the engine, install the bolts following the standard below.
CAUTION:
When installing transaxle assembly do not bring transaxle input shaft into contact with clutch cover.
- QR25DE engine models
- VQ35DE engine models
• Bleed the air from the clutch hydraulic system. Refer to
CL-7, "Air Bleeding Procedure"
• After installation, check oil level, and check for leaks and loose mechanisms. Refer to
.
: Transaxle to engine
: Engine to transaxle
Bolt symbol
A
B
C
D
E
F
Quantity
1
3
1
2
2
1
Bolt length “ ” mm
(in)
45
(1.77)
80
(3.15)
45
(1.77)
35
(1.38)
45
(1.77)
Tightening torque
N·m (kg - m, ft- lb)
35.3
(3.6, 26)
74.5
(7.6, 55)
42.6
(4.3, 31)
48.0
(4.9, 35)
PCIB1972E
: Transaxle to engine
: Engine to transaxle
Bolt No.
A
B
C
Quantity
4
2
4
Bolt length “ ” mm
(in)
55
(2.17)
116.5
(4.59)
45
(1.77)
Tightening torque N·m
(kg - m, ft- lb)
74.5
(7.6, 55)
50.0
(5.1, 37)
AWDIA0188ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст