Nissan Altima L32. Instruction — part 1424

TM-40

< DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52A]

TRANSAXLE ASSEMBLY

3. Install differential side bearing outer race to clutch housing using

Tool.

CAUTION:

Replace differential side bearing and differential side bear-

ing outer race as a set.

4. Install oil channel (1) on mainshaft side.

CAUTION:

When installing oil channel, fit the rib (A) of oil channel into

the processed area of the spot facing (B).

5. Install mainshaft front bearing to clutch housing using Tool.

CAUTION:

Be careful with the orientation of mainshaft front bearing.

6. Install mainshaft bearing retainer (1) to clutch housing and

tighten bolt to the specified torque.

CAUTION:

Install with punched surface facing up.

7. Install magnet to clutch housing.

Tool number

: ST30720000 (J-25405)

WCIA0275E

PCIB1921E

Tool number

: ST33200000 (J-26082)

PCIB0939E

2

: Mainshaft front bearing

3

: Oil channel

PCIB1938E

PCIB1859E

TRANSAXLE ASSEMBLY

TM-41

< DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

8. Install final drive assembly into clutch housing.

9. Install input shaft assembly, mainshaft assembly, and reverse

idler gear assembly into clutch housing.

CAUTION:

• Wrap tape to the spline of input shaft so as not to damage

the input shaft oil seal.

• Be careful with the orientation of reverse idler shaft.

10. Install striking rod assembly (1) into clutch housing.

CAUTION:

• Check that return spring is securely seated in the groove

on return pin.

SCIA0888E

SCIA0964E

PCIB1857E

PCIB1866E

TM-42

< DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52A]

TRANSAXLE ASSEMBLY

11. Install 1st-2nd shift fork (1) and 1st-2nd fork rod (2) and then

install retaining pin to 1st-2nd shift fork.

CAUTION:

• Do not reuse retaining pin.

• Be careful with the orientation of 1st-2nd shift fork and

1st-2nd fork rod.

• Assemble retaining pin from the direction shown until it

becomes flush with the end surface of 1st-2nd shift fork.

12. Install 3rd-4th shift fork (1) to 3rd-4th coupling sleeve.

CAUTION:

Be careful with the orientation of 3rd-4th shift fork.

13. Install 5th-6th shift fork (1) and 5th-6th fork rod (2) and then

install retaining pin to 5th-6th shift fork.

CAUTION:

• Do not reuse retaining pin.

• Be careful with the orientation of 5th-6th shift fork and

5th-6th fork rod.

• Assemble retaining pin from the direction shown until it

becomes flush with the end surface of 5th-6th shift fork.

14. Install 3rd-4th fork rod (2) and then install retaining pin to 3rd-4th

shift fork (1).

CAUTION:

• Do not reuse retaining pin.

• Be careful with the orientation of 3rd-4th fork rod.

• Assemble retaining pin from the direction shown until it

becomes flush with the end surface of 3rd-4th shift fork.

15. Install reverse shift fork (1) and reverse fork rod (2).

CAUTION:

Be careful with the orientation of reverse shift fork and

reverse fork rod.

PCIB1856E

PCIB1855E

PCIB1852E

PCIB1853E

PCIB1875E

TRANSAXLE ASSEMBLY

TM-43

< DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

16. Rotate striking lever of striking rod assembly as shown. Then

rotate reverse fork rod to a position where bracket of reverse

fork rod does not interfere with striking lever of striking rod

assembly.

17. Install retaining pin to reverse shift fork (1).

CAUTION:

• Do not reuse retaining pin.

• Assemble retaining pin from the direction shown until it

becomes flush with the end surface of reverse shift fork.

18. Install selected differential side bearing adjusting shim(s) and differential side bearing outer race.

• For selection of adjusting shim(s), refer to

TM-49, "Adjustment"

.

19. Install selected reverse idler gear adjusting shim onto reverse idler gear assembly.

• For selection of adjusting shim, refer to

TM-49, "Adjustment"

.

20. Install selected input shaft rear bearing adjusting shim onto input shaft.

• For selection of adjusting shim, refer to

TM-49, "Adjustment"

.

21. Install selected striking rod adjusting shim onto striking rod assembly.

• For selection of adjusting shim, refer to

TM-49, "Adjustment"

.

22. Install shifter lever oil seal (1) and striking rod oil seal (2) to tran-

saxle case using suitable tool.

CAUTION:

• Do not reuse shifter lever oil seal and striking rod oil seal.

• When installing, do not incline shifter lever oil seal and

striking rod oil seal.

• Do not damage transaxle case.

PCIB1851E

2

: Reverse fork rod

PCIB1850E

Dimension “H”

: 0 - 1.0 mm (0 - 0.039 in)

PCIB1818E