Nissan Altima L32. Instruction — part 1423
TM-36
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
18. Remove striking rod shim (1), striking rod adjusting shim (2),
mainshaft rear bearing adjusting shim (3), input shaft rear bear-
ing adjusting shim (4), and reverse idler gear adjusting shim (5).
19. Remove retaining pin of reverse shift fork (1) using suitable tool.
20. Rotate striking lever of striking rod assembly as shown. Then
rotate reverse fork rod to a position where bracket of reverse
fork rod does not interfere with striking lever of striking rod
assembly.
21. Pull out reverse shift fork and reverse fork rod.
22. Remove retaining pin of 5th-6th shift fork (1) using suitable tool.
23. Remove retaining pin of 3rd-4th shift fork (1) using suitable tool.
24. Pull out 3rd-4th fork rod (2).
PCIB1858E
2
: Reverse fork rod
PCIB1850E
PCIB1851E
2
: 5th-6th fork rod
PCIB1852E
PCIB1853E
TRANSAXLE ASSEMBLY
TM-37
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
25. Pull out 5th-6th shift fork (1) and 5th-6th fork rod (2).
26. Pull out 3rd-4th shift fork (1).
27. Remove retaining pin of 1st-2nd shift fork (1) using suitable tool.
28. Pull out 1st-2nd shift fork and 1st-2nd fork rod (2).
29. Remove striking rod assembly (1).
30. Remove gear components from clutch housing in the following
procedure.
a. Remove a set of input shaft assembly, mainshaft assembly, and
reverse idler gear assembly by tapping the tip of input shaft from
the back of the clutch housing with a plastic hammer.
CAUTION:
Always withdraw mainshaft straight out. Failure to do so
can damage resin oil channel on clutch housing side.
b. Remove final drive assembly.
PCIB1854E
PCIB1855E
PCIB1856E
PCIB1857E
SCIA0964E
TM-38
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
31. Remove magnet from clutch housing.
32. Remove mainshaft bearing retainer and then mainshaft front
bearing from clutch housing using Tool.
CAUTION:
Do not damage clutch housing, mainshaft front bearing,
and oil channel.
33. Remove oil channel from clutch housing.
34. Remove differential side bearing outer race from clutch housing
using Tool.
CAUTION:
Do not damage clutch housing and differential side bearing
outer race.
35. Remove input shaft oil seal from clutch housing using suitable
tool.
CAUTION:
Do not damage clutch housing.
36. Remove differential side oil seal from clutch housing using suit-
able tool.
CAUTION:
Do not damage clutch housing.
PCIB1859E
Tool number
:KV381054SO (J-34286)
PCIB0937E
Tool number
:KV381054SO (J-34286)
PCIB0938E
SCIA0398E
PCIB1874E
TRANSAXLE ASSEMBLY
TM-39
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Assembly
INFOID:0000000004201597
1. Install differential side oil seal (1) to clutch housing using Tool
(A).
CAUTION:
• Do not reuse differential side oil seal.
• When installing, do not incline differential side oil seal.
• Do not damage clutch housing.
2. Install input shaft oil seal (1) to clutch housing using Tool (A).
CAUTION:
• Do not reuse input shaft oil seal.
• When installing, do not incline input shaft oil seal.
• Do not damage clutch housing.
Dimension “H”
: -0.5 - 0.5 mm (-0.020 - 0.020 in)
Tool number
: ST33400001 (J-26082)
PCIB1864E
Dimension “H”
: 1.1 - 2.1 mm (0.043 - 0.083 in)
Tool number
: ST35321000 ( — )
PCIB1814E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст