Nissan Altima L32. Instruction — part 1422
TM-32
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
Disassembly
INFOID:0000000004201596
1. Remove drain plug and gasket from clutch housing.
2. Remove plug bolt and then plug (with ABS models) or speedom-
eter pinion gear (without ABS models) and O-ring from clutch
housing.
1.
Differential side bearing outer
race (clutch housing side)
2.
Differential side bearing (clutch
housing side)
3.
Speedometer drive gear
4.
Differential case
5.
Final gear
6.
Differential side bearing (tran-
saxle case side)
7.
Differential side bearing outer
race (transaxle case side)
8.
Differential side bearing adjusting
shim
9.
Pinion mate shaft
10. Side gear
11. Side gear thrust washer
12. Pinion mate gear
13. Pinion mate thrust washer
14. Retaining pin
Replace parts as a set
PCIB1964E
PCIB1834E
TRANSAXLE ASSEMBLY
TM-33
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3. Remove plug and gasket from transaxle case.
4. Remove park/neutral position (PNP) switch (1) from transaxle
case.
5. Remove back-up lamp switch (2) and plunger from transaxle
case.
CAUTION:
Do not lose plunger.
6. Remove air breather tube (3) from transaxle case.
7. Remove guide bolt from transaxle case.
8. Remove retaining pin using suitable tool and then remove selec-
tor lever from transaxle case.
9. Remove transaxle case bolts.
PCIB1865E
PCIB1835E
PCIB1836E
PCIB1837E
PCIB1838E
TM-34
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
10. Remove bore plug from transaxle case.
CAUTION:
• Do not damage transaxle case.
• Access bore plug from cutout (A) of transaxle case when
removing.
11. Remove transaxle case following the procedures below.
a. Expand snap ring at mainshaft rear bearing accessing from the
bore plug hole. Then pull up transaxle case from clutch housing
until snap ring comes off.
b. With shifter lever A (1) held in the position shown, remove tran-
saxle case from clutch housing.
CAUTION:
Do not drop each adjusting shim.
NOTE:
Make sure to hold shifter lever A (1) in the position shown. Oth-
erwise transaxle case cannot be removed from clutch housing.
12. Remove oil gutter A (1) and oil gutter B (2) from transaxle case.
PCIB1839E
PCIB1840E
PCIB1808E
A
: Tab of oil gutter
PCIB1841E
TRANSAXLE ASSEMBLY
TM-35
< DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
13. Remove snap ring from transaxle case.
14. Remove retaining pin using suitable tool and then remove shifter
lever A and shifter lever B from transaxle case.
15. Remove differential side bearing outer race from transaxle case
using Tool, then remove differential side bearing adjusting shim
from transaxle case.
CAUTION:
Do not damage transaxle case.
16. Remove differential side oil seal from transaxle case using suit-
able tool.
CAUTION:
Do not damage transaxle case.
17. Remove shifter lever oil seal (1) and striking rod oil seal (2) from
transaxle case.
CAUTION:
Do not damage transaxle case.
PCIB1842E
PCIB1844E
Tool number
:KV381054SO (J-34286)
PCIB0936E
SCIA0397E
PCIB1846E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст