Nissan Altima L32. Instruction — part 1191
REAR SUSPENSION ASSEMBLY
RSU-9
< ON-VEHICLE MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
4. Measure distance (A) from rear side.
5. Push the vehicle slowly ahead to rotate the wheels 180
°
degrees (1/2 a turn).
• If the wheels have rotated more than 180
° degrees (1/2 a
turn), try the above procedure again from the beginning. Never
push vehicle backward.
6. Measure distance (B) from front side.
7. Adjust toe-in by turning adjusting bolts.
NOTE:
Toe changes about 1.5 mm (0.059 in) [One side] with each grad-
uation of the adjusting bolt.
8. Tighten the adjusting bolt nuts to the specified torque.
Total toe-in : Refer to
SFA234AC
LEIA0008E
LEIA0009E
Adjusting bolt nuts
: Refer to
RSU-10
< REMOVAL AND INSTALLATION >
REAR SUSPENSION ASSEMBLY
REMOVAL AND INSTALLATION
REAR SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000004205679
SEDAN
AWEIA0127GB
1.
Cap
2.
Shock absorber insulator
3.
Shock absorber seal
4.
Bound bumper
5.
Shock absorber
6.
Suspension arm
7.
Connecting rod mount bracket
8.
Connecting rod
9.
Upper rubber seat
10. Coil spring
11. Lower rubber seat
12. Knuckle
13. Knuckle bushing
14. Rear lower link
15. Suspension arm bushing
REAR SUSPENSION ASSEMBLY
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
COUPE
16. Front lower link
17. Radius arm
18. Front member stay (LH)
19. Front member stay (RH)
20. Stabilizer bar clamp
21. Bushing
22. Stabilizer bar
23. Member stopper
24. Rear suspension member
25. Rear member stay
26. Ball seat
Front
AWEIA0128GB
1.
Cap
2.
Shock absorber insulator
3.
Shock absorber seal
4.
Bound bumper
5.
Shock absorber
6.
Suspension arm
7.
Connecting rod mount bracket
8.
Connecting rod
9.
Upper rubber seat
10. Coil spring
11. Lower rubber seat
12. Knuckle
13. Knuckle bushing
14. Rear lower link
15. Suspension arm bushing
RSU-12
< REMOVAL AND INSTALLATION >
REAR SUSPENSION ASSEMBLY
Removal and Installation
INFOID:0000000004205680
Removal
CAUTION:
Before removing the rear suspension assembly, disconnect the ABS wheel sensor from the assembly.
Failure to do so may result in damage to the sensor wires and the sensor becoming inoperative.
1. Remove the center exhaust tube with muffler(s). Refer to
EX-6, "Removal and Installation"
(QR25DE) or
EX-12, "Removal and Installation"
(VQ35DE).
2. Remove brake caliper assembly and reposition aside, without disconnecting the hydraulic hose, using
power tools. Refer to
BR-35, "BRAKE CALIPER ASSEMBLY : Exploded View"
• Leave the brake hydraulic hose connected to the brake caliper.
• Do not depress the brake pedal, or the caliper piston will pop out.
• Do not pull or twist the brake hydraulic hose.
3. Remove brake rotor. Refer to
BR-35, "BRAKE CALIPER ASSEMBLY : Exploded View"
.
4. Disconnect parking brake cable from knuckle. Refer to
PB-6, "PEDAL TYPE : Exploded View"
type),
PB-7, "LEVER TYPE : Exploded View"
(lever type).
5. Remove rear wheel sensors. Refer to
BRC-63, "Removal and Installation"
(ABS),
(TCS/ABS),
BRC-236, "Removal and Installation"
(VDC/TCS/ABS).
6. Remove lower shock absorber nuts using power tools.
7. Remove lower control arm link adjusting bolt and arm. Refer to
RSU-13, "Removal and Installation"
.
8. Remove upper ball joint nut and cotter pin. Refer to
9. Disconnect radius rod member side. Refer to
RSU-15, "Removal and Installation"
.
10. Disconnect lower link adjusting bolt. Refer to
RSU-14, "Removal and Installation"
11. Remove knuckle. Refer to
.
12. Remove stabilizer bar. Refer to
RSU-16, "Removal and Installation"
.
13. Disconnect lower link adjusting bolt. Refer to
RSU-14, "Removal and Installation"
14. Disconnect member harness.
15. Support the rear suspension assembly using a suitable jack.
16. Remove the suspension member nuts and member stay bolts using power tools.
17. Lower the rear suspension assembly.
Installation
Installation is in the reverse order of removal.
• Check the rear wheel alignment and adjust if necessary. Refer to
16. Front lower link
17. Radius arm
18. Front member stay (LH)
19. Front member stay (RH)
20. Stabilizer bar clamp
21. Bushing
22. Stabilizer bar
23. Member stopper
24. Rear suspension member
25. Rear member stay
26. Ball seat
Front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст