Nissan Rogue. Instruction — part 569
IGNITION COIL
EM-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
IGNITION COIL
Exploded View
INFOID:0000000011279954
Removal and Installation
INFOID:0000000011279955
REMOVAL
1. Remove air cleaner and air duct. Refer to
.
2. Disconnect the harness connector from the ignition coil.
3. Remove the ignition coil.
CAUTION:
Discard any ignition coil which has been dropped or shocked.
INSTALLATION
Installation is in the reverse order of removal.
1. Ignition coil
2. Spark plug
3. Rocker cover
AWBIA2265ZZ
EM-42
< REMOVAL AND INSTALLATION >
ROCKER COVER
ROCKER COVER
Exploded View
INFOID:0000000011279956
Removal and Installation
INFOID:0000000011279957
REMOVAL
1. Remove intake manifold. Refer to
EM-29, "Removal and Installation"
2. Remove wheel and tire (RH) using a power tool.
3. Remove engine under cover. Refer to
EXT-37, "ENGINE UNDER COVER : Removal and Installation"
4. Remove fender protector side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
5. Remove drive belt. Refer to
EM-15, "Removal and Installation"
.
6. Use a suitable jack (A) to securely support the bottom of the
engine (1) and the transaxle assembly (2).
CAUTION:
Put a piece of wood or an equivalent as the supporting sur-
face and secure in a stable condition.
7. Remove the RH engine mount torque rod. Refer to
1. Oil filler cap
2. Rocker cover
3. Rocker cover gasket
A. Refer to INSTALLATION
Engine front
AWBIA1317GB
ALBIA0894GB
ROCKER COVER
EM-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
8. Remove A/C line bracket bolt.
9. Remove harness grounds from engine mounting bracket (RH).
10. Remove harness retainers from engine mounting bracket (RH).
11. Remove the engine mounting bracket (RH). Refer to
12. Remove the engine mounting bracket (LH). Refer to
13. Disconnect the PCV hose.
14. Disconnect harness connector from intake valve timing control solenoid valve. Refer to
15. Disconnect harness connector from intermediate valve timing control solenoid valve. Refer to
16. Disconnect harness connector from exhaust valve timing control solenoid valve. Refer to
17. Disconnect harness connector from camshaft position sensors. Refer to
.
18. Remove the spark plugs. Refer to
EM-19, "Removal and Installation"
19. Loosen the bolts in the numerical order as shown using power
tool.
20. Remove the rocker cover and the rocker cover gasket. Discard
the rocker cover gasket.
CAUTION:
Do not reuse the rocker cover gasket.
21. Remove the oil filler cap, (if necessary).
INSTALLATION
: Engine front
AWBIA1985ZZ
ALBIA0836GB
EM-44
< REMOVAL AND INSTALLATION >
ROCKER COVER
1. Apply liquid gasket to the position shown (A) with the following
procedure:
a. Apply liquid gasket to joint part of No.1 camshaft bracket (1) and
cylinder head.
b. Apply liquid gasket in a 90
° degree angle (B).
• Use Genuine Silicone RTV Sealant, or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
2. Install rocker cover gasket to rocker cover.
NOTE:
The rocker cover gasket must be securely installed in the groove in the rocker cover.
3. Install the rocker cover and rocker cover gasket onto the cylinder head.
4. Tighten the rocker cover bolts to specification in two steps in the
order shown.
5. Installation of the remaining components is in the reverse order of removal.
6. Inspect for engine oil leaks. Refer to
.
(B)
: 10 mm (0.39 in)
(C)
: 4 mm (0.16 in)
(D)
: 5 mm (0.20 in)
ALBIA0837GB
Step 1
: 1.96 N·m (0.20 kg-m, 17 in-lb)
Step 2
: 8.33 N·m (0.85 kg-m, 74 in-lb)
ALBIA0836GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст