Nissan Rogue. Instruction — part 708
STEERING KNUCKLE
FSU-21
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
16. Open the slot using a suitable tool (A). Separate the steering
knuckle (1) from the front coil spring and strut.
CAUTION:
Do not drop steering knuckle.
INSPECTION AFTER REMOVAL
Check for deformity, cracks and damage on each part, replace if necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse the wheel hub lock nut.
• Do not reuse the cotter pin.
• Do not reuse steering knuckle upper bolt nut.
• Do not reuse steering knuckle lower nut.
• Check the wheel alignment. Refer to
.
• Adjust the neutral position of the steering angle sensor. Refer to
ALDIA0492ZZ
FSU-22
< UNIT REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
UNIT REMOVAL AND INSTALLATION
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000011277060
Removal and Installation
INFOID:0000000011277061
REMOVAL
1. Remove the column hole cover. Refer to
2. Remove bolt and separate steering column from steering gear pinion shaft.
CAUTION:
With the steering linkage disconnected, the spiral cable may snap by turning the steering wheel
beyond the limited number of turns. Secure the steering wheel during removal of the front suspen-
sion member.
3. Remove the fender protector (LH/RH). Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installa-
4. Remove the nut and separate the stabilizer connecting rod from the stabilizer bar (LH/RH). Refer to
5. Remove the nut and separate the outer socket from the steering knuckle (LH/RH). Refer to
6. Remove the nut and bolt and separate the transverse link from steering knuckle (LH/RH). Refer to
7. Remove the engine side cover. Refer to
EXT-37, "ENGINE UNDER COVER : Removal and Installation"
8. Remove front exhaust mount. Refer to
9. Disconnect heated oxygen sensor 2. Refer to
10. Remove oxygen sensor bracket.
1.
Front suspension member
2.
Rebound insulator stopper
3.
Front suspension member stay
4.
Rebound stopper
A.
Refer to installation.
AWEIA0374ZZ
FRONT SUSPENSION MEMBER
FSU-23
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
11. Remove rear torque rod. Refer to
.
12. Set suitable jack under front suspension member.
13. Remove bolts and remove front suspension member stay from
vehicle.
14. Remove bolts and nuts from front suspension member.
15. Gradually lower jack to remove front suspension member from
vehicle.
CAUTION:
Secure front suspension member to suitable jack while
removing it.
16. If necessary, remove bolts and nuts, and then remove transverse link, stabilizer bar, and steering gear
from front suspension member.
INSPECTION AFTER REMOVAL
Check the front suspension member for significant deformation, cracks, or damages. Replace it if necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• With the steering linkage disconnected, the spiral cable may snap by turning the steering wheel
beyond the limited number of turns. Secure the steering wheel during installation of the front sus-
pension member.
• When connecting the steering column (1) to the steering gear
pinion shaft (2), be sure that the gap (A) lines up with the joint
retaining bolt hole.
• Make sure the bolt is in the correct direction, as shown, and is
securely seated in the groove.
• Install the suspension member bolts in the order shown.
• Perform final tightening of installation position between front sus-
pension member and transverse links (rubber bushing) under unladen condition with tires on level ground.
• Check wheel sensor harness for proper connection. Refer to
BRC-130, "FRONT WHEEL SENSOR :
.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust the neutral position of the steering angle sensor. Refer to
WEIA0181E
AWGIA0320ZZ
Temporary tightening
: 1
→ 2
Final tightening (Specified torque)
: 3
→ 6
Bolts 3-5
94 N·m (9.6 kg-m, 69 ft-lb)
Bolts 6
76 N·m (7.8 kg-m, 56 ft-lb)
: Front
ALEIA0222ZZ
FSU-24
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT COIL SPRING AND STRUT
UNIT DISASSEMBLY AND ASSEMBLY
FRONT COIL SPRING AND STRUT
Exploded View
INFOID:0000000011277063
Disassembly and Assembly
INFOID:0000000011277064
DISASSEMBLY
CAUTION:
Do not damage the piston rod when removing components from the front coil spring and strut.
1. Install Tool (A) to the front coil spring and strut.
CAUTION:
When installing Tool (A), wrap a shop cloth around the front
coil spring and strut to protect the parts from damage.
2. Secure Tool (A) in a vise.
3. Install a suitable tool to strut rod.
4. Slightly loosen the piston rod lock nut.
WARNING:
1.
Strut mount insulator
2.
Strut mount bearing
3.
Front spring upper rubber seat
4.
Front suspension bound bumper
5.
Front coil spring
6.
Front spring lower rubber seat
7.
Stabilizer connecting rod
8.
Strut
9.
Steering knuckle
AWEIA0375ZZ
Tool number
: ST35652000 ( – )
AWEIA0262ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст