Nissan Rogue. Instruction — part 1051
SE-70
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
4. Remove screw (A), then using a suitable tool release clips and
pawls and remove seat cushion outside finisher (LH).
: Clip
: Pawl
5. Using a suitable tool, release clips and pawls, then remove seat
cushion outer finisher (RH)
: Clip
: Pawl
6. Remove bolts (A) and seatback frame.
NOTE:
Seatback pad and trim removed for clarity.
7. Release J-hooks (A) and fasteners (B), then route seatbelt
buckles through seat cushion and remove seat cushion pad and
seat cushion trim.
ALJIA1451ZZ
ALHIA0381ZZ
ALJIA1450ZZ
ALJIA1452ZZ
SECOND ROW SEAT
SE-71
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
8. Remove hog rings, then separate seat cushion trim from seat
cushion pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Make sure hook fastener is pressed into place after seat cushion
trim is assembled.
• Smooth out all wrinkles during assembly.
LH SEAT : Armrest Assembly
INFOID:0000000011280473
DISASSEMBLY
1. Remove second row seat LH. Refer to
SE-39, "Removal and Installation"
2. Using a suitable tool release clips and remove seatback board
(1).
: Clip
3. Remove screw (A), then release pawls and remove armrest fin-
isher (1).
: Pawl
ALJIA1453ZZ
PIIB3356J
ALJIA1413ZZ
ALJIA1411ZZ
SE-72
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
4. Remove bolts (A) and armrest.
5. Release J-Hooks (A) and fasteners (B), then remove seatback
center trim from seatback center pad.
6. Using a suitable tool release metal clips and pawls and remove
cup holder (1).
: Metal clip
: Pawl
7. Press the headrest holder lock button, then lift headrest up and remove.
8. Reach up behind the armrest assembly, release the headrest
holder locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing headrest holder, check its orien-
tation (front/rear and right/left).
ALJIA1412ZZ
ALJIA1454ZZ
ALJIA1444ZZ
PIIB4084J
SECOND ROW SEAT
SE-73
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
9. Release J-Hooks (A) from armrest frame and remove armrest
lower pad.
10. Remove armrest trim, then remove armrest pad.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Make sure fastener is pressed into place after armrest trim is assembled.
• Smooth out all wrinkles during assembly.
LH SEAT : EZ Entry Cable
INFOID:0000000011280474
DISASSEMBLY
NOTE:
LH shown : RH similar
1. Remove second row seat LH. Refer to
SE-39, "Removal and Installation"
2. Using a suitable tool release clips and remove seatback board
(1).
: Clip
3. Remove screw (A), then using a suitable tool release pawls and
remove armrest finisher (1).
: Pawl
ALJIA1445ZZ
ALJIA1413ZZ
ALJIA1411ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст