Nissan Rogue. Instruction — part 1050
SE-66
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
LH SEAT
AWJIA1619ZZ
1.
Headrest (center)
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Cup holder
5.
Armrest inner finisher
6.
Armrest trim
7.
Armrest pad
8.
Armrest outer finisher
9.
Armrest fold flat strap
10. Seat cushion trim
11. Seat cushion pad
12. Seat cushion silencer
13. Seat cushion pad wire
14. Bolt cover
15. Seat cushion outer finisher (RH)
16. Seat cushion inner finisher (RH) 17. Seat belt buckle (center)
18. Seat cushion frame
19. Seat belt buckle (LH)
20. Seat cushion center finisher (RH) 21. Seat cushion center finisher (LH)
22. Rear bolt cover (RH) (with third
row seat)
23. Front bolt cover (RH)
24. Front bolt cover (LH)
25. Rear bolt cover (LH) (with third
row seat)
26. Seat slide control lever
27. Seat cushion slide (RH)
SECOND ROW SEAT
SE-67
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
LH SEAT
LH SEAT : Seatback
INFOID:0000000011280471
DISASSEMBLY
1. Remove second row seat LH. Refer to
SE-39, "Removal and Installation"
2. Using a suitable tool release clips and remove seatback board
(1).
: Clip
3. Remove screw (A), then using a suitable tool release clip and
pawls, then remove seat cushion outside finisher (LH).
: Clip
: Pawl
4. Remove screw (A), then using a suitable tool release clips and
pawls and remove armrest finisher (1).
: Clip
: Pawl
28. Seat cushion slide (LH)
29. Seat cushion slide cable
30. Seat cushion outer finisher (LH)
31. Seat cushion inner finisher (LH) 32. Armrest inner finisher
33. Recline release cable
34. Seatback frame
35. Recline device
36. Recline device finisher
37. Headrest (LH)
38. Seatback luggage upper board
39. Seatback luggage board
40. Seatback pad wire
41. Armrest lower pad
42. Seatback center trim
43. Seatback center pad
44. Seatback trim
45. Seat belt retractor finisher
46. Seatback pad
47. Seat belt retractor (center)
48. Fold flat strap
49. Armrest bracket
50. Armrest frame
51. Seat belt retractor inner finisher
52. Seat belt retractor outer finisher
Clip
Pawl
ALJIA1413ZZ
ALJIA1451ZZ
ALJIA1411ZZ
SE-68
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
5. Remove bolts (A) and armrest.
6. Press the headrest holder lock button, then lift headrest up and remove.
7. Reach up behind the seatback pad, release the headrest holder
locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing headrest holder, check its orien-
tation (front/rear and right/left).
8. Release pawls and remove recline handle finisher.
9. Release pawls and remove seatbelt retractor outer finisher.
10. Release J-hooks (A) then release fastener (B) and remove seat-
back pad and seatback trim.
11. Remove seat belt retractor (center) bottom anchor bolt then route seat belt retractor (center) through rear
seat cushion and seatback.
12. Remove hog rings, then separate seatback trim from seatback
pad.
NOTE:
Remove all pieces of hog rings and discard them.
: Hog ring
ALJIA1412ZZ
PIIB4084J
ALJIA1448ZZ
ALJIA1449ZZ
SECOND ROW SEAT
SE-69
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
13. Remove bolts (A) and seatback frame from seat cushion frame.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat-
back trim and seatback pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Make sure hook fastener is pressed into place after seatback trim
is assembled.
• Smooth out all wrinkles during assembly.
LH SEAT : Seat Cushion
INFOID:0000000011280472
DISASSEMBLY
1. Remove second row seat LH. Refer to
SE-39, "Removal and Installation"
2. Remove screw (A), then using a suitable tool release pawls and
remove armrest finisher (1).
: Pawl
3. Remove bolts (A) and armrest.
ALJIA1450ZZ
PIIB3356J
ALJIA1411ZZ
ALJIA1412ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст