Nissan Rogue. Instruction — part 1208
TM-204
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
AIR BREATHER
AIR BREATHER
Exploded View
INFOID:0000000011279423
Removal and Installation
INFOID:0000000011279424
REMOVAL
1. Remove air cleaner and air duct. Refer to
EM-26, "Removal and Installation"
.
2. Remove air breather hose from transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not bend the air breather hose to prevent damage to the hose.
• Insert air breather hose to the end of air breather.
• Insert air breather hose (1) to air breather tube (2) all the way
to the curve of the tube.
• Insert air breather hose to air breather tube so that the paint
mark (A) is facing upward.
Air breather
Air breather hose
Air breather tube
Transaxle assembly
: Vehicle front
JSDIA5140ZZ
ALDIA0501ZZ
OIL PAN
TM-205
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000011279425
COMPONENT PARTS LOCATION
Removal and Installation
INFOID:0000000011279426
REMOVAL
1. Remove engine under cover. Refer to
TM-205, "Removal and Installation"
2. Remove drain plug from oil pan and then drain the CVT fluid.
3. Remove drain plug gasket.
4. Remove the oil pan bolts, and then remove the oil pan and oil pan gasket.
5. Remove the magnets from the oil pan.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse drain plug gasket.
• Do not reuse O-ring.
• Completely clean the iron powder from the magnet area of oil pan and the magnets.
Transaxle assembly
Oil pan gasket
Oil pan
Drain plug
Drain plug gasket
Magnet
Overflow plug
O-ring
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA4194GB
TM-206
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
OIL PAN
Install the oil pan to the transaxle case with the following procedure.
1. Install the oil pan gasket to the oil pan.
CAUTION:
• Completely wipe out any moisture, oil, and old gasket from the oil pan gasket surface and bolt
hole of oil pan and transaxle case.
• Do not reuse oil pan gasket.
2. Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan bolts.
3. Tighten the oil pan bolts in the order shown to the specified
torque.
4. Tighten the oil pan bolts again clockwise from (1) shown to the
specified torque.
Inspection
INFOID:0000000011279427
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check the CVT fluid level and leakage. Refer to
: Front
AWDIA1136ZZ
INPUT SPEED SENSOR
TM-207
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INPUT SPEED SENSOR
Exploded View
INFOID:0000000011279428
Removal and Installation
INFOID:0000000011279429
REMOVAL
1. Remove battery tray. Refer to
PG-79, "Removal and Installation (Battery Tray)"
2. Remove the starter motor. Refer to
STR-21, "Removal and Installation"
.
3. Disconnect the input speed sensor harness connector.
4. Remove the input speed sensor bolt and remove the input speed sensor.
5. Remove the O-ring from the input speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply CVT fluid to the O-ring.
Inspection and Adjustment
INFOID:0000000011279430
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
Input speed sensor
O-ring
Transaxle assembly
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA4131GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст