Nissan Rogue. Instruction — part 1207
TM-200
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
KEY INTERLOCK CABLE
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000011279417
Removal and Installation
INFOID:0000000011279418
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1. Move shift selector to the “N” position.
2. Remove the shift selector knob.
3. Move shift selector to the “P” position.
4. Remove the center console assembly. Refer to
IP-19, "Removal and Installation"
5. Press the pawls (B) of the key interlock cable slider (A) while
sliding it in the direction of the casing cap (C), and separate the
adjusting holder (D) and slider (A).
6. Remove the key interlock cable from the shift selector.
7. Remove the steering column covers. Refer to
8. Remove instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
1.
Key cylinder
2.
Clip
3.
Key interlock cable
4.
Shift selector assembly
ALDIA0491ZZ
(E)
:Key interlock rod
JSDIA1797ZZ
KEY INTERLOCK CABLE
TM-201
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
9. Lift clip (A) in the direction of the arrow (
C) and remove in the
direction of the arrow (
D).
10. Disconnect the key interlock cable from the key cylinder.
11. Disengage the clip and disconnect the key interlock cable from
the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• While pressing the detent rod (B) down, slide the key interlock
cable slider (A) toward the key interlock rod (D) side, and install the
adjusting holder (C) and key interlock rod.
CAUTION:
• Do not squeeze the pawls on the key interlock cable slider
when holding the slider.
• Do not apply force in a perpendicular direction to the key
interlock rod when sliding the slider.
• Install the adjusting holder (A) onto the key interlock rod (B), then
install the casing cap (C) onto the shift selector cable bracket (D).
CAUTION:
• When installing the key interlock cable, do not bend or twist
the cable forcefully.
• After connecting the key interlock cable to the shift selector
cable bracket, be sure to check that the casing cap is com-
pletely fastened to the cable bracket. If the casing cap is
easily displaced, replace the key interlock cable.
Inspection
INFOID:0000000011279419
INSPECTION AFTER INSTALLATION
• Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
• The key can be removed only when the selector lever is in the “P” position.
• It must not be possible to turn the ignition switch to LOCK when the selector lever is not in the “P” position.
(1)
:Key interlock cable
(B)
:Key cylinder
JSDIA1798ZZ
:Interlock cable in lock position
JSDIA1800ZZ
JSDIA1799ZZ
TM-202
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
TCM
TCM
Exploded View
INFOID:0000000011279420
Removal and Installation
INFOID:0000000011279421
CAUTION:
• Do not impact the TCM when removing or installing TCM.
• When replacing TCM and transaxle assembly simultaneously, perform "ADDITIONAL SERVICE
WHEN REPLACING TCM AND TRANSAXLE ASSEMBLY". Refer to
• Before replacing TCM, save TCM data using "ADDITIONAL SERVICE WHEN REPLACING TCM".
Refer to
• When replacing TCM, note the “CVTF DETERIORATION DATE” value displayed on CONSULT “CON-
FORM CVTF DETERIORTN” in MAINTENANCE BOOKLET, before start the operation.
REMOVAL
1. Disconnect the battery negative terminal. Refer to
2. Remove the air duct (inlet). Refer to
3. Disconnect the TCM harness connector (A).
4. Remove the TCM nuts and remove TCM from bracket.
INSTALLATION
Installation is in the reverse order of removal.
Bracket
Bracket
TCM
: Vehicle front
: N·m (kg-m, in-lb)
JSDIA5129GB
(1)
: TCM
: Front
ALDIA0500ZZ
TCM
TM-203
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Adjustment
INFOID:0000000011279422
ADJUSTMENT AFTER INSTALLATION
Perform "ADDITIONAL SERVICE WHEN REPLACING TCM". Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст