Nissan Rogue. Instruction — part 1206
TM-196
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CVT SHIFT SELECTOR
1. Install the lock pin (2) onto the shift selector handle (3).
2. Install the shift selector handle cover (1) onto the shift selector
handle.
3. Shift the selector lever to “N” position.
4. Pull and hold the shift selector handle button (A) in the direction
shown (
) using a suitable tool and insert shift selector handle
(B) into the shift selector assembly (C) until a slight touch is felt.
5. Release shift selector handle button (A) and continue to push
down (
) on shift selector handle (B) into shift selector assem-
bly (C) until you feel it click into place.
CAUTION:
Do not strike the selector lever handle to press it into place.
6. After installing shift selector handle (A), pull the handle in the
direction shown (
) to check that it does not become discon-
nected.
Inspection
INFOID:0000000011279413
INSPECTION AFTER INSTALLATION
• Check the shift selector position. Refer to
.
• Check that shift lock can be forcible release. Refer to
TM-29, "SHIFT LOCK SYSTEM : System Description"
.
JSDIA3654ZZ
AWDIA1253ZZ
AWDIA1254ZZ
CONTROL CABLE
TM-197
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL CABLE
Exploded View
INFOID:0000000011279414
Removal and Installation
INFOID:0000000011279415
CAUTION:
Always apply the parking brake before performing removal and installation.
REMOVAL
1. Apply the parking brake.
CAUTION:
Make sure the vehicle cannot move with the parking brake applied.
2. Remove battery tray. Refer to
PG-79, "Removal and Installation (Battery Tray)"
3. Remove the control cable nut (
) and remove the control cable
(1) from the instruction lever (2).
1.
Shift selector
2.
Control cable
3.
Retainer grommet
4.
Bracket A
5.
Lock plate
6.
Bracket B
7.
Instruction lever
8.
Transaxle assembly
Front
AWDIA1147ZZ
: Front
JSDIA4147ZZ
TM-198
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CONTROL CABLE
4. Remove the lock plate (1) and remove the control cable (2) from
bracket (3).
5. Remove the control cable (2) from bracket (1).
6. Remove retainer grommet (3) by pushing upward.
7. Remove the center console assembly. Refer to
IP-19, "Removal and Installation"
8. Disconnect the tip (A) of control cable and remove the socket
(B) from the shift selector assembly.
9. Remove the control cable.
INSTALLATION
Installation is in the reverse order of removal.
• Pay attention to the following when connecting the control cable to the shift selector assembly.
1. When connecting the control cable (1) to the shift selector
assembly (2), face the grooved surface of the rib (A) up and
insert the control cable until it stops.
NOTE:
Apply multi-purpose grease to control cable eye before installa-
tion.
: Front
JSDIA4148ZZ
: Front
ALDIA0520ZZ
JSDIA4145ZZ
JSDIA1624ZZ
CONTROL CABLE
TM-199
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2. Install the socket (A) onto the shift selector assembly.
CAUTION:
• Place the socket onto the shift selector assembly, then
fasten it in place from above.
• Check that the pulling on the socket does not disconnect
it.
Inspection and Adjustment
INFOID:0000000011279416
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT position. Refer to
INSPECTION AFTER ADJUSTMENT
Check the CVT shift selector position after the adjustment. Refer to
.
JSDIA1810ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст