Nissan Rogue. Instruction — part 1111
AIR BAG DIAGNOSIS SENSOR UNIT
SR-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Replace the air bag diagnosis sensor unit if it has been
dropped or sustained an impact.
• Do not strike the air bag diagnosis sensor unit.
INSTALLATION
Install air bag diagnosis sensor unit in the reverse order of removal.
CAUTION:
• Do not reuse the air bag diagnosis sensor unit bolt and nuts.
• The air bag diagnosis sensor unit must always be installed with the label arrow mark "
" pointing
toward the front of the vehicle for proper operation.
• Do not damage the air bag diagnosis sensor unit harness connectors during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT that the ECU discrimi-
nated number (identification number) or part number of the new replacement air bag diagnosis sen-
sor unit matches the ECU discriminated number (identification number) or part number of the
replaced (old) air bag diagnosis sensor unit.
NOTE:
If the ECU discriminated number or part number of the new replacement air bag diagnosis sensor unit differs
from the ECU discriminated number or part number of the replaced air bag diagnosis sensor unit, reconfirm
the parts information and verify that the correct air bag diagnosis sensor unit was installed.
SGI787
SR-28
< REMOVAL AND INSTALLATION >
FRONT SEAT BELT PRE-TENSIONER
FRONT SEAT BELT PRE-TENSIONER
Removal and Installation
INFOID:0000000011279769
The front seat belt has two pre-tensioners. One pre-tensioner is part of the seat belt retractor and the other is
a lap belt pre-tensioner. For removal and installation refer to
SB-8, "SEAT BELT RETRACTOR : Removal and
(lap belt pretensioner).
FRONT SEAT BELT BUCKLE SWITCH
SR-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT SEAT BELT BUCKLE SWITCH
Removal and Installation
INFOID:0000000011279770
The front seat belt buckle switch is part of the front seat belt buckle. For removal and installation of the front
seat belt buckle, refer to
SB-11, "FRONT SEAT BELT BUCKLE : Removal and Installation"
.
SR-30
< REMOVAL AND INSTALLATION >
OCCUPANT CLASSIFICATION SYSTEM
OCCUPANT CLASSIFICATION SYSTEM
Removal and Installation
INFOID:0000000011279771
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Do not use air tools or electric tools for servicing.
Removal
1. Slide front seat passenger side to full forward position.
2. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
3. Remove occupant classification system control unit screws (A).
4. Disconnect the harness connector (B) and remove occupant
classification system control unit (1).
CAUTION:
• Replace the occupant classification control unit if it has
been dropped or sustained an impact.
• Do not strike the occupant classification control unit.
Installation
Installation is in the reverse order of removal.
WARNING:
• Zero point reset must be performed every time the occupant classification system control unit is
removed/replaced.
CAUTION:
• Do not damage the harness connector during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
.
OCCUPANT CLASSIFICATION SYSTEM SENSORS
Removal
1. Remove the front seat passenger side. Refer to
SE-35, "PASSENGER SIDE : Removal and Installation"
2. Remove seat cushion outer finisher (RH).
a. For instruction seat:
i.
Remove snap ring (1) as shown (
) using a suitable tool, then
remove the recline lever (2).
ALHIA0364ZZ
AWJIA1562ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст