Nissan Rogue. Instruction — part 270
DAS
C1BC2-00 REAR RIGHT WHEEL SENSOR
DAS-251
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
4. Perform “All DTC Reading”.
Is DTC “C1BC2-00”, “U1000-00” or other DTC detected?
YES (“C1BC2-00”)>>Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-260, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> Inspection End.
DAS-252
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BC3-00 REAR LEFT WHEEL SENSOR
C1BC3-00 REAR LEFT WHEEL SENSOR
DTC Description
INFOID:0000000011277422
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Rear left wheel sensor
• Rear left sensor rotor
• ABS actuator and electric unit (control unit)
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Start the engine.
2. Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1 minute.
3. Stop the vehicle.
4. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
5. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BC3-00” detected?
YES
>> Proceed to
DAS-252, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277423
1.
CHECK REAR LH WHEEL SENSOR SYSTEM
With CONSULT
Perform “Self Diagnostic Result” of “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BC3-00
RL WHEEL SENSOR
(Rear left wheel sensor)
When a malfunction is detected in rear left wheel sensor system.
DAS
C1BC3-00 REAR LEFT WHEEL SENSOR
DAS-253
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
4. Perform “All DTC Reading”.
Is DTC “C1BC3-00”, “U1000-00” or other DTC detected?
YES (“C1BC3-00”)>>Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-260, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> Inspection End.
DAS-254
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BC4-00 DECEL G SENSOR
C1BC4-00 DECEL G SENSOR
DTC Description
INFOID:0000000011277424
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Yaw rate/side/decel G sensor [integrated in ABS actuator and electric unit (control unit)]
• ABS actuator and electric unit (control unit)
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Ride Control (brake) function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BC4-00” detected?
YES
>> Proceed to
DAS-254, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277425
1.
CHECK DECEL G SENSOR SYSTEM
With CONSULT
Perform “Self Diagnostic Result” of “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “All DTC Reading”.
Is DTC “C1BC4-00”, “U1000-00” or other DTC detected?
YES (“C1BC4-00”)>>Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-260, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BC4-00
DECEL G SENSOR
(Decel G sensor)
When a malfunction is detected in decel G sensor system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст